Forum Replies Created
-
Posts
-
Re: Hotpoint condenser drier mods info please.
Yes, the rear panel as I understand it must be changed or there can be, mhm, issues.
The mod is said to take 40-60 mins to do so, 20 seems more than a bit low.
Given what you’re saying and that I know some have “allegedly” not been modified correctly I’d be very suspicious as well.
And you’re bang on as, if you do anything and it’s not right guess who’ll get the blame for any subsequent problems! :rolls:
K.
Re: Hotpoint condenser drier mods info please.
There’s no info on the models Steve, the only way to check it is on the HP website as they’ve not released a list of the affected machines. 😕
K.
Re: Britannia Range BR-SI-9S6-L-G Selector switch
Think you’ll need more info on it as they changed them IIRC so there can be two or three different ones used.
It’s probably this one but I’m not 100{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} sure:
http://shop.ukwhitegoods.co.uk/a03411-o … tor-switch
K.
Re: Miele G1252 salt filler seal
I think that’s a Miele only part, no info on it at all so I’m afraid you’re pretty much at their mercy. 🙁
K.
Re: BEKO CDA539FW frozen fridge compartment
It’s usually not the PCB but the thermistors that are an issue.
It’s electronic so, no clicking.
The two usual suspects are:
https://shop.ukwhitegoods.co.uk/4394720 … air-sensor
http://shop.ukwhitegoods.co.uk/43947201 … dge-sensor
Door I’ve no idea on, I can only think it could be an adjustment of some kind. 😕
K.
Re: Coldplay
Didn’t think they’d let old duffers like you into that sort of thing, might blow your hearing aid up. 😉
K.
Re: heating element resistance values
Works fine here. 😕
You can just use email though, same thing really.
No idea on the part, Dave’s been trying to figure that out but, a part number is a part number. If we order up that part number then they will all be the same barring any alterations and, if they’ve one’s been altered, they’re all altered.
For the machine a heater is being fitted to the element fitting is the important factor, it has to have the same fitting at the tub and enough length to reach the clamp or whatever on the machine/s it’s intended for but beyond that almost anything can be changed.
This is one of the reasons that part numbers are used, the part can alter but the part number will often stay the same. Equally, the part number can also alter with changes on some.
And, why we tell people all the time not to use dimensions and images alone to identify most parts. You cannot trust that information on every occasion as it can alter without notice.
K.
Re: Liebherr Fridge Freezer Temperature Issue
I didn’t know if it was an air driven one Eddie but yeah, a definite possibility as well.
K.
Re: Liebherr Fridge Freezer Temperature Issue
We will need the service number to look up anything for you, that’s just the current iteration of that model there can be 20 or more variants over time.
How to find that is here:
https://ukwhitegoods.freshdesk.com/supp … pare-parts
However it would sound like either a thermistor or compressor problem. If the former, not too bad. If the latter, bad news.
K.
Re: Please help diagnose oven fault – cuts out when hot
If you’re not testing it with a thermometer then how do you know what the temperature in the cavity is?
If the main stat is faulty as I think it may be, all that’ll happen is it will heat and heat till the overheat kicks in and shuts it down. The thermostat will not shut the elements off as it should.
The temperature in that scenario is not really relevant.
K
Re: Please help diagnose oven fault – cuts out when hot
Sounds as if it’s cutting out on the overheat so it will most probably be the main oven thermostat or the overheat that’s the problem and not the element.
K.
