[lmcc67]

Hi Kwatt,
Thank you for your assistance here. Really helpful. Would you know I can access the thermostat? I can take the cover off the light but not sure where to go from there.

[lmcc67]

Re: Bosch SGS43A32 not filling

hiya I took the bottom off and it seems like the I think its the circulation pump its part 5600039406 has some water coming from it. I t seems like it is not connected properly into the bottom part that drains the water away, it has some play in it where it connects. Not sure if it is suppose to have a bit of play or pushed right in!!!!!! not sure really what i am looking for!!!!!

[lmcc67]

Re: Bosch SGS43A32 not filling

I can not see any screws to take the base off

[lmcc67]

Re: Bosch SGS43A32 not filling

I tipped it on its back but was not able to take the bottom off. The water is filing up on the side container and letting the water in but after the machine drains once it just drains and drains and stops when i open the door fully. It is leaking but then if it is leaking is there anything you can do to stop it leaking?

[lmcc67]

Re: Bosch SGS43A32 not filling

also any ideas where the anti-flood switch is please

[lmcc67]

Re: Bosch SGS43A32 not filling

I have tipped it forward and water has poured out. I have managed to get the sides off but do not seam to be able to take the bottom off, any ideas?? also any ideas where the main circulating pump and drive shaft are
thank you Martin

[lmcc67]

Re: Bosch SGS43A32 not filling

yes it does Martin and I pulled it out and water did come out of it. Is there a way of fixing it or has it had it days?

[lmcc67]

Re: Bosch SGS43A32 not filling

I have read on other posts that the problem may be the /safety valve needs replacing. Where would I find this please

[lmcc67]

Re: Hygena Select APL 8224/1 Dishwasher not filling with wat

‘Check in order: water supply, water valve, fill chamber/matrix.’
thank you will do hopefully this will resolve the problem, thank you

[lmcc67]

ok thank you for your prompt reply but we cannot afford anymore money so it would have to be one of these, do you think you could advise on which one is better than the others please please

[lmcc67]

not sure wherethere to go for indesit, hoover, or hotpoint, please help

[lmcc67]

hi, i just wanted to say again a big thank you to all the brilllant electricians/technicians/engineers on this site as by taking their advice and reading through lots of their replies to other people with similar problems that i had with my vacum cleaner, i was able to fix my vacum, just by changing the belt thanx Goatboy, once again many many thanks, you guys are brillant!!!!!!!

[lmcc67]

hi kwatt
thank you for your terminology correction, never thought of that!!!! just thought “vacuming” was an American term as i work for an American and he uses that term!!!!!!
thank you also for your advice on my vaccum, i have just checked filters they seem pretty clean, checked the brush roll seems clear but doesnt spin when vaccum is on!!! maybe the belt?

[lmcc67]

hi
there were two broken wires that were touching at the bottom of the door that i fixed then put them in casing,
then cleaned out all the filters that were quite blocked and cleaned out all the water spray arms. put rinse aid in the machine that i had stopped using a while back as i was using 3 in 1 tablets, and i pressumed there was enough rinse aid in them until i read the advise on your site,
i was able to do this and take the parts on and off by reading replies and advice on your site, so thank you so so much!!!!!!

[lmcc67]

i have only had this hoover for 2 months

[Author]

Posts