PGS

Forum Replies Created

Viewing 15 posts - 106 through 120 (of 321 total)
1 2 3 … 7 8 9 … 20 21 22
  • Author
    Posts
  • May 21, 2009 at 4:08 pm in reply to: Zanussi ZWX 1605W #287238
    PGS
    Participant

    Re: Zanussi ZWX 1605W

    Blocked pressure chamber ?

    May 21, 2009 at 9:02 am in reply to: Zanussi t/d td4113 91609206901 #287443
    PGS
    Participant

    Re: Zanussi t/d td4113 91609206901

    So what was it?

    April 29, 2009 at 3:22 pm in reply to: LG WM-14225FD drum jerks after 10 min #285232
    PGS
    Participant

    Re: LG WM-14225FD drum jerks after 10 min

    take back of and you will see it, the senser is at the bottom of the stator.

    April 28, 2009 at 7:50 pm in reply to: Hotpoint BWD129 #285276
    PGS
    Participant

    Re: Hotpoint BWD129

    Chees Jim. So the spider doesnt come as a seperate part, its drum and shaft assy?

    April 28, 2009 at 4:41 pm in reply to: LG WM-14225FD drum jerks after 10 min #285230
    PGS
    Participant

    Re: LG WM-14225FD drum jerks after 10 min

    Check wiring to motor connections and hall senser located on the stator. My bet is Hall senser as 99{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} of motor dont need to be replaced as its usually this senser.

    April 23, 2009 at 3:06 pm in reply to: 3 phase motor #283927
    PGS
    Participant

    Re: 3 phase motor

    Hi if you test between phases the resistance for example 1and 2 shoud be the same as 2 and 3 and 1 and 3 get the pattern.

    April 15, 2009 at 5:22 pm in reply to: Candy CDI1012/1-80 #283263
    PGS
    Participant

    Re: Candy CDI1012/1-80

    Thanks Mike!

    April 3, 2009 at 4:24 pm in reply to: LG washing machine drum bearings. #282108
    PGS
    Participant

    Re: LG washing machine drum bearings.

    Probably one of the easiest bearing jobs you will ever do. As far as cost goes, thats pretty much depends on you.

    March 27, 2009 at 7:24 pm in reply to: Servis M6602W Diagnostics #281469
    PGS
    Participant

    Re: Servis M6602W Diagnostics

    Does it have thejanus PCB on it?

    March 25, 2009 at 9:25 pm in reply to: Baumatic cooker BT2760ss #281306
    PGS
    Participant

    Re: Baumatic cooker BT2760ss

    Kirk is it the MCB or RCD thats triping. I thimk you need to get your mega out matey.

    March 18, 2009 at 6:45 pm in reply to: Miele CTD #280690
    PGS
    Participant

    Re: Miele CTD

    Nine out of ten its the TOC. Remember to test it with laundry in.

    March 8, 2009 at 9:15 pm in reply to: Zanussi TLE 1116w #279081
    PGS
    Participant

    Re: Zanussi TLE 1116w

    Ive cancelled the fault code on this machine and ran it 4 times over the weekend and fault has not re-ocurred. Could this fault on pulley senser be a 1 off or should I replace senser with mod kit. Any tips appreciated.

    March 3, 2009 at 5:22 pm in reply to: Zanussi TLE 1116w #279080
    PGS
    Participant

    Re: Zanussi TLE 1116w

    Dave Ive sent you a PM cheers.

    March 3, 2009 at 5:11 pm in reply to: Zanussi TLE 1116w #279078
    PGS
    Participant

    Re: Zanussi TLE 1116w

    Cheers Dave the appliance stops working after just a few seconds as if it hasnt sensed the pully senser

    February 18, 2009 at 1:54 pm in reply to: miele t284 dryer #276242
    PGS
    Participant

    Re: miele t284 dryer

    Remember when you test it to put damp clothes in or you will be looking for a fault that aint there.

  • Author
    Posts
Viewing 15 posts - 106 through 120 (of 321 total)
1 2 3 … 7 8 9 … 20 21 22