[recall]

Re: Hotpoint ff78p

also had to change the rear cond fan as well on a few. same symtoms but cab between fridge and freezer will be toatsing..
and obv fan will be stalled…

[recall]

Re: Hotpoint Condensor relay?

no problemo….
thats taken from a live partfinder and manual 😉
recall….

[recall]

Re: Hotpoint Condensor relay?

ans:—-

b4 d.c. 94 the relay coil was feed from the ON/OFF on the timer and after d.c. 93 it was feed directly off the live in to the timer (no switch).
as per manual 5405770 is/2
sorry cant get diag on here…..

but on timer it move from c10 to b10 basically….
glad 2 help

[recall]

Re: Hotpoint Condensor relay?

no they do stay energised until the door is opened as some dryers when off do the intermittent tumble…
they relay is only a means of interlock for when door is opened.
i got puzzled at first when i heard a coil buzz but quick look at drawings and a new relay later all sorted….
cheers recall

[recall]

Re: WMA PCBs,ANY CLUES TO BLOWN TRACKS OR ICs ?????????????

chaffed wires to motor as well. takes em out for sure..
usually around the back of the front weight….

[recall]

Re: INDESIT WI RANGE, NON STOP TIMER CLICKING ROUND?+moan ti

how do you think we feel…
we do nothing but that useless things and they still can scratch heads many times…. change module works for 5 months back again do the same and goes the same time… arrgghhhh… talk about regular customers 😕

[recall]

Re: Hotpoint Condenser TDC30P

The only time ive ever had to get at the chamber is once in 10 years, the only reason for that is fluff was holding the float up when empty..
very quick way to clear valve which ive done before is to drain the chamber from rear, fill bottle full slide into position and slap it fully home, water pressure blows the fluff out of the back hole..
but recommend full strip down though.. (use the other method if youre in those houses you wipe feet on your way out, and dont want to lay down) 😉

[recall]

Re: creda t/d 37643

as far as im aware the jk or zbn is just the timer identifier, it should be stamped on the timer somewhere…
glad to help… 😀

[recall]

Re: creda t/d 37643

sorry found the zbn connections

this is using prev numbers in jk post to zbn timer
ie 9 cycle stat is 10 on zbn and so on so
9 now 10
3 now 2
1 now 8
17 now 5
19 now 3

😯 any use????

[recall]

Re: creda t/d 37643

hi
is it the zbn or the jk model??
jk6011 connections
red/bla -motor:19
bro/bla- motor:17
blu – motor:1
pin/whi – door:3
bla/whi – cycle stat:9
i think theres a link from 15-23 could be internal tho
if struggling still have got convert leaflet in office 2mora…..

[recall]

Re: creda t/d 37643

whats the manufacturer of the timer youve got…

[recall]

Re: Frozen Veg in Crisper of Hotpoint FF Fridge/Freezer FFA7

if heavy frost/ice uniform on back poss module but had a couple of diverter valves block allowing cooling on freezer only cycles.
not sure how much modules are. prob best to get hpt out…

FYI tho they run on fuzzy logic. i.e. they switch comprssor and diverter on and off to factory defaults until it saves a better on off pattern to attain the selected temps.. if you get me… it uses this then if a thermistor fails to carry on as normal, but it cant tell if thermistor drifts…
cheers recall

[recall]

Re: Frozen Veg in Crisper of Hotpoint FF Fridge/Freezer FFA7

how old is the m/c, and is there a build up of ice in the corner of the gutter as well??

[recall]

Re: Hotpoint Condenser TDC30P

water light coming on then its crud in water bottle valve,
v long screwdriver and wizz out valve at rear of the bottle also scoop out all the crud that collects in the rear of the condensor chamber around the drain hole and near the fan at the back.
oh how i love that job……
😡

[recall]

Re: Resistive heating

theres a kit that indesit fse have to fit which comprises of a new felt panel and some boots to fit on the element terminals, also removing the side felt panels.
so poss due to the m/c leaking (as they do) and felt conducting en vola! fire!!

[Author]

Posts