rickard

Forum Replies Created

Viewing 15 posts - 46 through 60 (of 200 total)
1 2 3 4 5 … 12 13 14
  • Author
    Posts
  • June 20, 2016 at 11:04 am in reply to: Russell Hobbs t/d #438712
    rickard
    Participant

    Re: Russell Hobbs t/d

    Good Morning Yes I am trade and no would never buy this but got to try and repair it, I think I saw one a few years ago under Montpellier badge, The belt has no markings on it so cant even match it up with anything. Thanks Andy

    May 31, 2016 at 4:27 pm in reply to: Lamona HJA8704 #438093
    rickard
    Participant

    Re: Lamona HJA8704

    Hi Tim Thanks for the reply sorry I did mean 85 Mohms
    Andy

    February 9, 2016 at 3:28 pm in reply to: HOOVER WMH130D-80 #434793
    rickard
    Participant

    Re: HOOVER WMH130D-80

    After pulling my hair out with this one it has had a new PCB and two new thermal type door interlocks it still refused to unlock. After testing everything I decided to try a third interlock and hey presto it unlocked, This means that two brand new interlocks are faulty and will not unlock I tried to take one of the covers off and when I loosened the yellow cover I heard the latch unlock which means that they must be sticking inside. Is this a batch problem or are all hoover door locks rubbish. Andy

    January 28, 2016 at 10:00 pm in reply to: HOOVER WMH130D-80 #434792
    rickard
    Participant

    Re: HOOVER WMH130D-80

    Hi Dave
    It is the instant type
    Andy

    January 27, 2016 at 5:35 pm in reply to: HOOVER WMH130D-80 #434790
    rickard
    Participant

    Re: HOOVER WMH130D-80

    Hi Bryan and Dave
    Thanks for your reply’s. I have changed the door lock and pcb still the same and if I remove the plug it still will not unlock the door the only way to open the door is to twist the lock away from inside and then open the door which will stay unlocked until you start a programme. I am really stuck on this one as I have put a megger on it so no earth fault. any help appreciated
    Andy

    October 9, 2015 at 6:28 pm in reply to: Belling GHU60GE #430843
    rickard
    Participant

    Re: Belling GHU60GE

    Many thanks Don
    Andy

    July 30, 2015 at 6:59 pm in reply to: hotpoint BD32K2 #429214
    rickard
    Participant

    Re: hotpoint BD32K2

    Many thanks Andy MTR8002 spot on
    Cheers

    July 27, 2015 at 2:46 pm in reply to: hotpoint BD32K2 #429212
    rickard
    Participant

    Re: hotpoint BD32K2

    Thanks iadom
    That’s the latest one sent which was a plaset but the shaft is about half an inch to long. The original one sent c00293308 was a CK and that was half inch to long aswell
    Andy

    July 24, 2015 at 7:39 am in reply to: Miele KFN12924SD-1 #429083
    rickard
    Participant

    Re: Miele KFN12924SD-1

    Hi Bryan

    KFN12924SD-1 51/120477365 20A

    Thanks

    August 20, 2014 at 6:46 pm in reply to: Neff double oven #418118
    rickard
    Participant

    Re: Neff double oven

    Hi Martin it is defiantly EO 05 they have sent a picture of it to the agent

    August 13, 2014 at 9:17 pm in reply to: Beko WMD61 #417810
    rickard
    Participant

    Re: Beko WMD61

    Many Thanks Dave

    Andy

    August 1, 2014 at 9:41 pm in reply to: GEMM Commercial refrigeration #417374
    rickard
    Participant

    Re: GEMM Commercial refrigeration

    Thanks Bryan I tried everywhere but never came up with that site, will contact them monday

    July 18, 2014 at 9:04 pm in reply to: APM6855-1 Fridge Freezer #416851
    rickard
    Participant

    Re: APM6855-1 Fridge Freezer

    Hi Bob

    Thanks for the reply I have had a magnet on the freezer side to replicate the door shut and changed both sensors but still only get 120v to the fan motor connectors with the fan motor disconnected. I don’t know what to try next.

    Andy

    June 5, 2014 at 4:08 pm in reply to: siemens dishwasher #414880
    rickard
    Participant

    Re: siemens dishwasher

    Thanks Martin I have checked the outlet all ok and there is no signs of overfoaming, so I will go with the drain pump I just thought it odd that it does pump out at the start of cycle but not at the end
    Andy

    May 14, 2014 at 1:24 pm in reply to: new frost free #413644
    rickard
    Participant

    Re: new frost free

    Thanks Don

    Customer insists on frost free, I will go for the Hotpoint. many thanks for your good advise

    Andy

  • Author
    Posts
Viewing 15 posts - 46 through 60 (of 200 total)
1 2 3 4 5 … 12 13 14