whizzkid

Forum Replies Created

Viewing 14 posts - 16 through 29 (of 29 total)
  • Author
    Posts
  • in reply to: Help with Samsung Code #222668
    whizzkid
    Participant

    Re: Help with Samsung Code

    yes brian, i got that, but understood fault code to be bottom right hand segment on the right digit?

    sorry,
    i stand corrected if wrong

    cheers neil.

    in reply to: AEG washer drier fault code???? #222694
    whizzkid
    Participant

    Re: AEG washer drier fault code????

    would be an “f” code if it was an aeg?

    in reply to: Help with Samsung Code #222666
    whizzkid
    Participant

    Re: Help with Samsung Code

    fault code is refrigerator defrost sensor failure, sensor connection, wire cut, short circ or sensed temp is above 65c or below -50c.

    =replace defrost sensor to cure.

    in reply to: AEG washer drier fault code???? #222692
    whizzkid
    Participant

    Re: AEG washer drier fault code????

    E 10 is gonna be something to do with water fill problem.
    ie. water off, valve o/c, hydraulic circ etc

    in reply to: ESS Multi Assistance UK #216893
    whizzkid
    Participant

    Re: ESS Multi Assistance UK

    best avoided.
    i’ve been waiting over 6 months to get paid by this bunch
    keep getting fobbed off with all sorts of promises and excuses
    solicitors letter sent on wednesday giving them 7 days or it’s off to the courts!

    we shall wait and see….


    btw. solicitors letter only £2.00 + vat at thomashiggins.co.uk they are very efficient worth a look if u are owed money by anyone.

    cheers
    whizzkid

    in reply to: Teba TFC 1360 ss #209079
    whizzkid
    Participant

    Re: Teba TFC 1360 ss

    cheers guy’s
    thanks for your replies.
    off to the shop now!
    😆 neil

    in reply to: Zanussi fjs1225w #209044
    whizzkid
    Participant

    Re: Zanussi fjs1225w

    Agree with spuddy- may show E90 as well

    in reply to: SCHREIBER APM6855 #205711
    whizzkid
    Participant

    Re: SCHREIBER APM6855

    probably return air duct at bottom of freezer frozen up (like servis do,similar fridge freezer) seen a few recently.

    whizzkid
    Participant

    Re: Getting the belt on the tension pulley – Hpt condenser d

    On stretchy models ie vtd00p etc
    I use about 7 inches of 15mm copper tube, (just fits nicely over motor shaft), push through belt onto shaft, push down to stretch belt, roll drum round by hand (belt then slips off pipe onto shaft). – easy!

    whizzkid
    Participant

    Re: de dietrich dvf 110 ju 1/2 dishwasher – not draining

    cheers dave.thanks for that. any idea on prices for those parts?

    thankyou for your help
    neil

    in reply to: hi my zanussi jet system 5 hrs to wash #170996
    whizzkid
    Participant

    Re: hi my zanussi jet system 5 hrs to wash

    is drain hose too low? machine could be “syphoning”. make sure that the end off the drain hose is not stuffed down the standpipe, ( see instruction book installation guide) this will cause the machine to take a long time to reach level required also will have to keep topping up.

    hope this helps

    whizzkid.

    in reply to: electrolux wascator w100mp (commercial) #171183
    whizzkid
    Participant

    Re: electrolux wascator w100mp (commercial)

    cheers guy’s. i will try to tackle it! thanks for your help

    neil

    in reply to: t/bdx d/w #170275
    whizzkid
    Participant

    Re: t/bdx d/w

    There is also a kit available for this type of dishwasher (DWK 1 kit) it entails a new sump hose with additional pressure hose/pressure switch and a different type off inlet valve( without diaphram ) comes with fitting instructions. zanussi part number 50271495009. costs around £34 plus vat.

    in reply to: candy cr162k #166727
    whizzkid
    Participant

    Re: candy cr162k

    cheers chris

Viewing 14 posts - 16 through 29 (of 29 total)