a1al

Forum Replies Created

Viewing 15 posts - 16 through 30 (of 138 total)
1 2 3 … 8 9 10
  • Author
    Posts
  • March 13, 2012 at 8:09 pm in reply to: AEG Washing Machine Approx 2-3 years old #362513
    a1al
    Participant

    Re: AEG Washing Machine Approx 2-3 years old

    Priced customer for new module but he said it was to expensive.

    Have machine at workshop, I will get a better look when time permits.

    Thanks again

    March 13, 2012 at 8:06 pm in reply to: Electrolux ENL62981KS3 FRIDGE FREEZER DEAD! #362028
    a1al
    Participant

    Re: Electrolux ENL62981KS3 FRIDGE FREEZER DEAD!

    This one ended up being the Main pcb and the compressor at fault.
    Appliance scrapped.

    Thanks for your help and information Colin

    March 13, 2012 at 8:02 pm in reply to: Creda T601CW Reversing Timer ??? #362759
    a1al
    Participant

    Re: Creda T601CW Reversing Timer ???

    Just to update this post

    Timer done the trick

    Thanks again Jim

    March 13, 2012 at 8:00 pm in reply to: AEG Washer L76650 Will Only Empty #362883
    a1al
    Participant

    Re: AEG Washer L76650 Will Only Empty

    This ended up being a module

    Thanks for all the help

    March 13, 2012 at 7:58 pm in reply to: HNWF 7137 – 80 No HEAT?? #363299
    a1al
    Participant

    Re: HNWF 7137 – 80 No HEAT??

    Hi Everyone

    New module sorted this one.

    Srry about the delay in updating.

    March 13, 2012 at 7:56 pm in reply to: Hotpoint AQXGF149PIUK F01 Fault #369490
    a1al
    Participant

    Re: Hotpoint AQXGF149PIUK F01 Fault

    Hi Everyone

    Tested motor windings all three had same resistance reading and no leakage to earth.
    Tried the harness of an old machine, still F01
    Ordered up new module and card and machine is now working fine. (fitted module a week ago)

    Thanks again.

    February 24, 2012 at 8:06 pm in reply to: Hotpoint AQXGF149PIUK F01 Fault #369489
    a1al
    Participant

    Re: Hotpoint AQXGF149PIUK F01 Fault

    Thanks for that JJ

    I’ll give that a go as new module is £69.00 + vat + smart card @ £11.00

    Thanks

    February 24, 2012 at 9:22 am in reply to: Hotpoint AQXGF149PIUK F01 Fault #369487
    a1al
    Participant

    Re: Hotpoint AQXGF149PIUK F01 Fault

    Hi JJ
    What do you mean when you say…
    ”i would plug in another motor harness 1st just to confirm”
    Do you mean try new wiring and motor?
    Al

    February 23, 2012 at 2:29 pm in reply to: Hotpoint AQXGF149PIUK F01 Fault #369485
    a1al
    Participant

    Re: Hotpoint AQXGF149PIUK F01 Fault

    Thanks for your quick reply Kev

    Al

    February 23, 2012 at 1:59 pm in reply to: Miele G638plus – D/W not advancing through cycle. #369477
    a1al
    Participant

    Re: Miele G638plus – D/W not advancing through cycle.

    Hi

    I would have though if it was not continuing to heat the water to the proper temperature you would get a fault condition or the machine would at least stop.

    December 27, 2011 at 11:18 pm in reply to: Nordmende DFSN60 DW #366135
    a1al
    Participant

    Re: Nordmende DFSN60 DW

    Been out to two of these both had broken wires at bottom of door. Bad design where cables bend.

    November 16, 2011 at 9:24 am in reply to: HNWF 7137 – 80 No HEAT?? #363298
    a1al
    Participant

    Re: HNWF 7137 – 80 No HEAT??

    Thanks for your reply. have already quoted for and ordered a new module, will post how I get on.

    Thanks again

    November 14, 2011 at 9:57 am in reply to: HNWF 7137 – 80 No HEAT?? #363296
    a1al
    Participant

    Re: HNWF 7137 – 80 No HEAT??

    Just wondering if anyone knows if this machine should show a fault if the water heater does not heat? Or does hoover/candy not shows faults?

    November 8, 2011 at 10:52 pm in reply to: What is GIAS? #363357
    a1al
    Participant

    Re: What is GIAS?

    Thanks for that Jackal

    AL

    November 8, 2011 at 10:25 pm in reply to: What is GIAS? #363355
    a1al
    Participant

    Re: What is GIAS?

    Is it possible to get technical info from them without being a hoover or candy engineer?

    Also just wondering if there is another version of TDS Disc available I have the 2008 Version.

  • Author
    Posts
Viewing 15 posts - 16 through 30 (of 138 total)
1 2 3 … 8 9 10