A1TEC

Forum Replies Created

Viewing 15 posts - 196 through 210 (of 395 total)
1 2 3 … 13 14 15 … 25 26 27
  • Author
    Posts
  • March 18, 2010 at 8:34 pm in reply to: Panasonic Microwave #315487
    A1TEC
    Participant

    Re: Panasonic Microwave

    Could be magnatron fault, had a commercial Panasonic do the same thing.


    John.

    March 17, 2010 at 5:36 pm in reply to: Masterpart web site problems? #315070
    A1TEC
    Participant

    Re: Masterpart web site problems?

    Got a good city link lad up here, always leaves in the garage if im not in or he leaves me to last so he knows i”ll be in. 😀

    March 14, 2010 at 9:20 pm in reply to: Creda washing machine Mod W100 FW #314985
    A1TEC
    Participant

    Re: Creda washing machine Mod W100 FW

    I had a wm62 with the same problem, changed interlock and soldered wire on to blown track on board and linked it into the other side of the push-on connector. Done the job. 😉


    John.

    March 14, 2010 at 8:47 am in reply to: Raw #312895
    A1TEC
    Participant

    Re: Raw

    This always seems a difficult quest to find RAW machines, I have started buying one or two at a time off ebay, as they are like hens teeth in Scotland.
    I have always heard the stories of mountains of wm and wma machines down south, but have never been able to find out where exactly. 🙁

    It would be usefull if any such places existed, that the could say who and where they were and what they have. 😉

    John.

    March 12, 2010 at 8:32 pm in reply to: Stoves Gas Hob – GH607 HOB #312847
    A1TEC
    Participant

    Re: Stoves Gas Hob – GH607 HOB

    This is a job for a Gas Safe Registered engineer.

    March 12, 2010 at 10:33 am in reply to: Servis Quarts 6704 #314734
    A1TEC
    Participant

    Re: Servis Quarts 6704

    Think it’s a Hoover logic door seal that is a good fit.


    John.

    March 12, 2010 at 10:30 am in reply to: Hotpoint WF530 #314654
    A1TEC
    Participant

    Re: Hotpoint WF530

    HotDog wrote:check motor brushes

    Spot on Hotdog, carbons well worn. 😉


    Cheers

    John.

    March 11, 2010 at 7:48 pm in reply to: Yell.com #314709
    A1TEC
    Participant

    Re: Yell.com

    I just use their free listing, it works just aswell as a paid advert i think. 😉

    March 11, 2010 at 5:42 pm in reply to: creda simplicity. washer, w100fw #314662
    A1TEC
    Participant

    Re: creda simplicity. washer, w100fw

    Heater would have to be live to trip, does it fill?
    Could be door switch. 😉


    John.

    March 11, 2010 at 5:05 pm in reply to: MERRYCHEF PARTS #314649
    A1TEC
    Participant

    Re: MERRYCHEF PARTS

    Try your p.m again.


    John. 😆

    March 11, 2010 at 4:56 pm in reply to: MERRYCHEF PARTS #314647
    A1TEC
    Participant

    Re: MERRYCHEF PARTS

    P.M sent.

    March 11, 2010 at 4:51 pm in reply to: MERRYCHEF PARTS #314645
    A1TEC
    Participant

    Re: MERRYCHEF PARTS

    You can try http://WWW.MARREN.CO.UK
    they do Merrychef parts.

    I have two new door springs if you are interested they are handed i.e left and right.


    John.

    March 11, 2010 at 2:32 pm in reply to: MERRYCHEF PARTS #314643
    A1TEC
    Participant

    Re: MERRYCHEF PARTS

    Is it the pop up door machine?


    John.

    March 9, 2010 at 10:53 pm in reply to: Hotpoint WM62 #314442
    A1TEC
    Participant

    Re: Hotpoint WM62

    Much appreciated Kevin. 😀


    John.

    March 9, 2010 at 8:59 pm in reply to: Zanussi DE6744 Dish Washer #314444
    A1TEC
    Participant

    Re: Zanussi DE6744 Dish Washer

    Thanks Cliff, pnc is 911888019, will the manual sent cover this model?
    cheers,

    John.

  • Author
    Posts
Viewing 15 posts - 196 through 210 (of 395 total)
1 2 3 … 13 14 15 … 25 26 27