A1TEC

Forum Replies Created

Viewing 15 posts - 211 through 225 (of 395 total)
  • Author
    Posts
  • in reply to: Waring stick blender spares… #314411
    A1TEC
    Participant

    Re: Waring stick blender spares…

    Have you tried First Choice catering spares?

    John.

    in reply to: not been able to log on #314287
    A1TEC
    Participant

    Re: not been able to log on

    Wondered where you were. 😆
    Welcome back. 😉

    in reply to: White Knight Gas tumble Dryer #312844
    A1TEC
    Participant

    Re: White Knight Gas tumble Dryer

    From what you say, it sounds like rear bearing is worn.

    in reply to: Hotpoint WF530 #313149
    A1TEC
    Participant

    Re: Hotpoint WF530

    Thanks for that Kevin, much appreciated. 😉

    John.

    in reply to: zanussi zwf`s diagnosnics needed #313073
    A1TEC
    Participant

    Re: zanussi zwf`s diagnosnics needed

    Check your email. 😉


    John.

    in reply to: Proline TDV60 Dryer #312564
    A1TEC
    Participant

    Re: Proline TDV60 Dryer

    Will try and post one tomorrow night, as i have the beer out now and feet up. 😆

    John.

    in reply to: Proline TDV60 Dryer #312562
    A1TEC
    Participant

    Re: Proline TDV60 Dryer

    Thanks guys, i made a tool that dose just perfect. 😉


    John.

    in reply to: zanussi zwf 12070 #312227
    A1TEC
    Participant

    Re: zanussi zwf 12070

    No lap top required,all you need is a engineer with the service manual. 😆


    John.

    in reply to: zanussi zwf 12070 #312225
    A1TEC
    Participant

    Re: zanussi zwf 12070

    Have you accessed the machine diagnostics?,this will show fault code and point you in the correct direction, also the last fault can be reset.
    I had one do the same 2 months back, entered the diagnostics,reset and away the machine went.


    John.

    in reply to: zanussi zwf fails to go to wash cycle. #311987
    A1TEC
    Participant

    Re: zanussi zwf fails to go to wash cycle.

    Had one do the same 2 month back, machine has went to default setting.
    Diagnostics need to be accessed to reset machine, this may in turn show a fault code. 😉


    John.

    in reply to: Spare Part Pricing #312258
    A1TEC
    Participant

    Re: Spare Part Pricing

    Looking forward to the outcome of that investigation. 😆


    John.

    in reply to: british gas #287837
    A1TEC
    Participant

    Re: british gas

    funkyboogy wrote:had a few phone calls recently from mates that still work for b/g (poor sods)…

    morale at an all time low , check it out ………

    http://www.gas-leak.co.uk/index.php

    ally

    Had a look at that, now that is what i call a bad dream 🙁 I would hate to work in those sort of conditions, suppose it is similar to the bad old days of National Dont Care and their lovely management team. 😈

    Hope the BG guys get it sorted.

    in reply to: The Martin Conundrum #311506
    A1TEC
    Participant

    Re: The Martin Conundrum

    Was it the 0800 Repair site Lee?!!! 😆 😉

    in reply to: Rogue Traders BBC Wed 10th #311153
    A1TEC
    Participant

    Re: Rogue Traders BBC Wed 10th

    squadman wrote:How these idiots come up with all this amazes me after all Gordon Brown trades from a residential address so perhaps thats where they got the idea of rogue traders !

    Good one. 😆 😆 😆

    in reply to: Leisure CM10FRC (range cooker) #311032
    A1TEC
    Participant

    Re: Leisure CM10FRC (range cooker)

    Dose the top not remove on this style of cooker?
    I have done similar range cookers where you undo the whole spillage top to gain access to burner assembly etc.
    Worth checking as there is always a way to remove it. 😉

    John.

Viewing 15 posts - 211 through 225 (of 395 total)