Alanj

Forum Replies Created

Viewing 15 posts - 526 through 540 (of 757 total)
1 2 3 … 35 36 37 … 49 50 51
  • Author
    Posts
  • November 7, 2007 at 5:25 pm in reply to: Leaking Smeg D/W #233203
    Alanj
    Participant

    Re: Leaking Smeg D/W

    Its an adobe acrobat file Jim.

    Alan

    November 7, 2007 at 5:24 pm in reply to: Whirlpool AWM6140/3 #232654
    Alanj
    Participant

    Re: Whirlpool AWM6140/3

    By the way, robwash, machine is fixed 8) so thanks a lot for your help 😉

    Alan

    November 7, 2007 at 5:22 pm in reply to: Whirlpool AWM6140/3 #232653
    Alanj
    Participant

    Re: Whirlpool AWM6140/3

    Hi johnmac11,

    cheers john! I’ll have a look 😳

    Alan

    November 7, 2007 at 5:20 pm in reply to: smeg dishwasher dwd612 #233333
    Alanj
    Participant

    Re: smeg dishwasher dwd612

    MrDave

    Is there power coming out from mains suppresor 💡

    Alan

    November 7, 2007 at 5:15 pm in reply to: Leaking Smeg D/W #233201
    Alanj
    Participant

    Re: Leaking Smeg D/W

    Jim,

    you also have mail 😆

    Alan

    November 7, 2007 at 5:12 pm in reply to: Leaking Smeg D/W #233200
    Alanj
    Participant

    Re: Leaking Smeg D/W

    Hi Jim,

    from diagram of D/W Seals as follows tub seal SMG754131013 £7.70, says you also need to order door seal blocks SMG766330721 +SMG766330722 @ £1.88 each, seal along bottom of door or on tub SMG754131106 £8.40 all plus vat from Connect. I would suggest you call Smeg spares on 08704215982 as you will get trade discount on your credit card. HTH 😉

    Alan

    November 7, 2007 at 4:52 pm in reply to: Zanussi FS1555W #233349
    Alanj
    Participant

    Re: Zanussi FS1555W

    Hi Jim,

    I’ve had one of these myself and it was the pcb taken out by the pump. 😥

    Alan

    November 6, 2007 at 10:43 pm in reply to: Whirlpool AWM6140/3 #232651
    Alanj
    Participant

    Re: Whirlpool AWM6140/3

    [Johnmac11 wrote] Just about all of the models on SIOS now have wiring diagrams, resistance readings,fault codes and diagnostic programs.

    Where do you get this info on Sios?

    Alan

    November 6, 2007 at 10:34 pm in reply to: Leaking Smeg D/W #233196
    Alanj
    Participant

    Re: Leaking Smeg D/W

    Hi Jim,

    lower spray arm?

    Alan

    November 5, 2007 at 7:34 pm in reply to: Whirlpool AWM6140/3 #232648
    Alanj
    Participant

    Re: Whirlpool AWM6140/3

    Hi Robwash,

    have pm my fax no to you.

    Alan

    October 31, 2007 at 9:40 pm in reply to: AEG B2100-1 #232619
    Alanj
    Participant

    Re: AEG B2100-1

    Hi Simon,
    probably the thermal cut out, located in the wiring loom under top panel.
    Available from connect for £15.24 + vat, or from Masterpart £13.99 for 2. 😀

    Alan

    October 31, 2007 at 8:53 pm in reply to: Whirlpool AWM6140/3 #232646
    Alanj
    Participant

    Re: Whirlpool AWM6140/3

    by the way where did you get the fault codes from, for that model? I couldn’t find them listed on the known error codes. Are they on the Sios disc and if so where?

    Alan

    October 31, 2007 at 8:50 pm in reply to: Whirlpool AWM6140/3 #232645
    Alanj
    Participant

    Re: Whirlpool AWM6140/3

    Hi Robwash,

    thanks for the reply.It is zero and third light up. I thought it might have been an ntc fault, but wasn’t sure what reading ntc on heater should be. Heater tested out ok.

    Alan

    October 31, 2007 at 1:04 pm in reply to: LG WM1171FHB #232656
    Alanj
    Participant

    Re: LG WM1171FHB

    This one has a small weight on top and one weight at bottom of drumfront.

    Alan

    October 30, 2007 at 6:38 pm in reply to: WD420 drying fault #232579
    Alanj
    Participant

    Re: WD420 drying fault

    further to my last post, condenser itself could be gunged up and needs cleaning.

    Alan

  • Author
    Posts
Viewing 15 posts - 526 through 540 (of 757 total)
1 2 3 … 35 36 37 … 49 50 51