Alanj

Forum Replies Created

Viewing 15 posts - 541 through 555 (of 757 total)
1 2 3 … 36 37 38 … 49 50 51
  • Author
    Posts
  • October 30, 2007 at 6:36 pm in reply to: WD420 drying fault #232578
    Alanj
    Participant

    Re: WD420 drying fault

    Hi Clayside,

    sounds like the valve for the condenser is not working.Also check sump is clear of any blockages.Hope this helps. 🙂

    Alan

    October 24, 2007 at 5:02 pm in reply to: Eurocold Chest freezer C4BE-H #231945
    Alanj
    Participant

    Re: Eurocold Chest freezer C4BE-H

    Thanks expertcat,

    will do.

    Alan

    October 23, 2007 at 4:25 pm in reply to: smeg fridgeFAB32NE4 #231454
    Alanj
    Participant

    Re: smeg fridgeFAB32NE4

    Hi dna,

    faulty door switch?

    Alan

    October 22, 2007 at 8:32 pm in reply to: akz161/gr whirlpool double oven #231789
    Alanj
    Participant

    Re: akz161/gr whirlpool double oven

    If you e-mail me, your e-mail address I can send you some info.

    Alan

    October 22, 2007 at 8:31 pm in reply to: akz161/gr whirlpool double oven #231788
    Alanj
    Participant

    Re: akz161/gr whirlpool double oven

    Hi Dave,

    you could try this thread, http://www.ukwhitegoods.co.uk/modules.p … pic&t=4500.

    Alan

    October 22, 2007 at 6:35 pm in reply to: Hotpoint WMA60P #231780
    Alanj
    Participant

    Re: Hotpoint WMA60P

    Thanks a lot Jim for the info.

    Alan

    October 19, 2007 at 8:14 am in reply to: Servevast #231395
    Alanj
    Participant

    Re: Servevast

    Hi Roly16,

    used to be 01543 461336.

    Alan

    October 17, 2007 at 4:23 pm in reply to: hotpoint wd420 #231223
    Alanj
    Participant

    Re: hotpoint wd420

    Hi Paul,
    Stat is red spot Part No Hpt1605160. Is the fan secure to the shaft of the fan motor? You have to take heater box off to check. Otherwise customer quitting program before cool cycle/ no water from condenser valve.

    Alan

    October 17, 2007 at 4:15 pm in reply to: CTD20 not starting #231216
    Alanj
    Participant

    Re: CTD20 not starting

    Seamy,

    is it not a relay you have behind the facia? They are prone to going faulty part number Hpt1701624.

    Alan

    October 17, 2007 at 11:00 am in reply to: CTD00 – White spot #231201
    Alanj
    Participant

    Re: CTD00 – White spot

    Hi Steve,

    it should be the white spot 1703200 kit on this model.

    Alan.

    October 15, 2007 at 9:11 pm in reply to: Beko WMA1715 Dead #231056
    Alanj
    Participant

    Re: Beko WMA1715 Dead

    Hi John,

    you could try the motor plug. Have had a couple of these where the motor plug gets tugged out of the connector causing strange faults.

    Alan

    October 12, 2007 at 9:39 am in reply to: Stoves Range #230597
    Alanj
    Participant

    Re: Stoves Range

    Is there not a storage drawer or small flap that hinges down at bottom of appliance ❓ There’s usually a plate in there.

    Alan

    October 11, 2007 at 3:46 pm in reply to: Indesit wixe 127 #230505
    Alanj
    Participant

    Re: Indesit wixe 127

    Hi DOCTORDOOM,
    try disconnecting edge connectors from PCB and giving the connections a clean either with emery or a tooth brush. If that doesn’t work it’s probably a new PCB. EMW £34.90 + VAT.

    Alan

    October 10, 2007 at 11:36 am in reply to: Stoves range #228639
    Alanj
    Participant

    Re: Stoves range

    Is there a storage drawer at the bottom of that appliance?
    Numbers usually on a plate inside.

    Alan

    October 9, 2007 at 4:21 pm in reply to: neff thermostat #230291
    Alanj
    Participant

    Re: neff thermostat

    Hi Abbots,

    sorry abbots 08705543210.

    Alan

  • Author
    Posts
Viewing 15 posts - 541 through 555 (of 757 total)
1 2 3 … 36 37 38 … 49 50 51