[aroffauz]

Thanks Dave

[aroffauz]

Hi Dave – I understand the computer is time-based but why would it complete the quick wash including the rinses but not the cotton wash – Declan?

[aroffauz]

Hi Dave – thanks very much for your help — both washer dryers had the E73 fault and the wiring to the NTC had broken inside the insulation
Thanks Declan

[aroffauz]

Hi, Dave,
my email is declanodriscoll65@gmail.com
many thanks Declan

[aroffauz]

Hi Dave
my email is declanodriscoll65@gmail.com
Many thanks for your help
Declan

[aroffauz]

Re: Siemens Integrated dishwasher anti flood

Thanks Clive
I had come across the water metering tank seal and also the tub base seal – I just think they almost take more time than they are worth, by the time you have identified the leak(s) made a repair, refitted an integrated unit and hope that you do not get a recall. I was interested to hear other engineers experience with these
many thanks
Declan

[aroffauz]

Re: Bosch WAQ24461GB/14 – 8KG washing machine

Thanks Dave

[aroffauz]

Re: Miele W2659i Change Language

Hi Don
Thanks for your help
Declan 🙂

[aroffauz]

Re: Zanussi ZDT12011FA dishwasher pump reset

Hi Dave– thanks for your help
I had another look at it and found I had not fitted the contact on the new pressure sensor correctly 😳
all tested ok since
I appreciate your help
Many thanks Declan 🙂

[aroffauz]

Re: CDE129ALL Module /Wiring Mod/Smartcard

Hi Jim
It is the main Power Module in the base – apologies the commercial code is 80325700000.
The original module does not have a removable eeprom
I believe the new module C000254298 is correct
wiring mods C00142746 ( to valves and NTC) and C00142747( to fan motor) may be required.
Although there are three different smartcards listed ( the ” view notice” in partfinder says ” for correct programme card /file check description against the part code in partfinder CD or Servicenet parts list.” ( I have the partfinder CD but do not understand where to check and I do not have access to Servicenet parts list)
C00262025
C00262115
C00262966
This machine may have originally been supplied in Italy as it was part of a “POD” kitchen which was supplied with appliances already fitted . I don’t know if this has any bearing
Thanks Declan

[aroffauz]

Re: Indesit IWDC6105UK washer dryer

Thanks Hotdogs..I initially thought that might be the problem, I went back to read the technical notes re the 5 wire harness to the console.. My machine is the later model with 5 wires.thanks for your help Declan 🙂

[aroffauz]

Re: Indesit IWDC6105UK washer dryer

Thanks Hotgog
I swapped out the pressure switch with another , unfortunately the problem still persists ( pumps for about 1 second and then nothing)
This is good to know about the presure switches for the future
I appreciatte your advice
Thanks Declan 😀

[aroffauz]

Re: Indesit IWDC6105UK washer dryer

Hi Tim – thanks for your advice
I checked the continuity of the wiring from the dryer probe ntc to the module – all intact and reads correctly
I connected the ntc dryer wiring to another spare dryer unit
unfortunately the problem still persists

Thanks Declan 🙂

[aroffauz]

Re: Zanussi dishwasher ZDF14001SA overfilling

Hi Dave
The owner has no proof of purchase
I just interested in sorting the machine
Thanks for your suggestion all the same
Declan

[aroffauz]

Re: BCi 450 – C00143214 Integrated Dishwasher PCB Reset

Hello
I fitted the new PCB as I was experiencing the same problem as I have now
– there are no lights on the program panel and the program will not reset when I hold down the reset button. I presummed it was a control fault and fitted a new PCB – all other components appear ok and also the wiring on the door appears ok.
Thanks
Declan

[Author]

Posts