barryfast

Forum Replies Created

Viewing 15 posts - 46 through 60 (of 69 total)
1 2 3 4 5
  • Author
    Posts
  • April 28, 2006 at 12:59 pm in reply to: DIPLOMAT D/WASHER ADP8242 NR 018460402 #173487
    barryfast
    Participant

    Re: DIPLOMAT D/WASHER ADP8242 NR 018460402

    hi sent the board to QER but the chip has gone on it New board from
    HTM 89.99 + any one know of a cheaper one barry 😥

    April 6, 2006 at 9:04 pm in reply to: Hotpoint wmt 02 #171275
    barryfast
    Participant

    Re: Hotpoint wmt 02

    iadom thanks for your help in the end it was the board and thanks to EMW the m/c is now running so the board was the culprit replaced the carbons and door s/w as recomended Barryfast 😆

    March 26, 2006 at 3:05 pm in reply to: More New Faulty Elements #169636
    barryfast
    Participant

    Re: More New Faulty Elements

    HI I’VE FOUND ELEMENT KEPT IN STOCK CAN TAKE IN DAMPNESS IF
    STORED WITH NO HEAT, IF THEY GO DOWN TO EARTH I GET OUT THE
    BLOWLAMP START AT THE FURTHEST POINT AND WORK OUT THE DAMP
    ITS NOT FAILD YET BARRY FAST 💡

    March 17, 2006 at 10:45 pm in reply to: BEKO D 3422 FW DISHWASHER #169889
    barryfast
    Participant

    Re: BEKO D 3422 FW DISHWASHER

    THANKS FOR THAT BARRY

    March 8, 2006 at 11:18 pm in reply to: Servis M6011S w/m #167616
    barryfast
    Participant

    Re: Servis M6011S w/m

    Hi have repaired lot’s of the servis drums and hotpoint with epoxy resin
    and none back. 💡 barryfast

    February 21, 2006 at 8:48 pm in reply to: HOOVER HNWL3166 DRYER FAULT #163627
    barryfast
    Participant

    Re: HOOVER HNWL3166 DRYER FAULT

    hi up date water valve at fault thanks for all your help barryfast 😆

    February 21, 2006 at 8:18 pm in reply to: ZANUSSI W/D WDA1255W,NOT DRYING #163631
    barryfast
    Participant

    up date the water valve at fault thank for all your help barryfast

    February 6, 2006 at 10:22 pm in reply to: ZANUSSI W/D WDA1255W,NOT DRYING #163629
    barryfast
    Participant

    Hi THANKS FOR THAT I WILL LET YOU KNOW BARRYFAST

    January 25, 2006 at 5:21 pm in reply to: AEG dw42300 dishwasher #162172
    barryfast
    Participant

    Re: AEG dw42300 dishwasher

    HI DAVE THANKS FOR THE PROMP REPLY . BENDIGEDIG !! THATS FANTASTIC IN WELSH…
    WILL KEEP YOU POSTED
    BARRYFAST

    January 16, 2006 at 8:06 pm in reply to: tricity/bendix tm 310w 916710604/00 t/dryer #161100
    barryfast
    Participant

    Re: tricity/bendix tm 310w 916710604/00 t/dryer

    hi thanks for the reply will get stuck into it now and find the fault
    i hope barryfast I will be back 😉

    January 15, 2006 at 5:40 pm in reply to: indesit w101 fault #160877
    barryfast
    Participant

    Re: indesit w101 fault

    hi andy it fills then empties and repeats this process all day if u let it
    barry 😕

    January 14, 2006 at 10:39 am in reply to: indesit w101 fault #160875
    barryfast
    Participant

    Re: indesit w101 fault

    Hi no light on it onley on/off re-set will try heater / thermister thanks barryfast 😆

    January 13, 2006 at 3:16 pm in reply to: FJS 1425 E40 FAULT #160815
    barryfast
    Participant

    Re: FJS 1425 E40 FAULT

    aqualectric thanks a lot for info barryfast 😆

    January 10, 2006 at 10:42 pm in reply to: Zanussi ZSF 6150 D/W #160186
    barryfast
    Participant

    Re: Zanussi ZSF 6150 D/W

    reaper wrote:Thanks Chris.

    Wow! I’ve perused this document the machine is one with 4 contacts to the ntc -an inbuilt turbidity sensor,(an infra red feedback device to tell you how dirty the pots are) plus the temperature sensor- I’m impressed.

    I’ve seen this question asked before on here and wondered what the outcome was, it would nice to get the feedback as it might be a common fault. I bet theres a Zanussi engineer who’s had loads of these and fixed them in 10 minutes.

    Suspect main Board (relay) or ntc device.

    Hi got the same prop the p/r s/w near the front feed,s the heater connectins1&3 cloesd wen full a1 relay on maine board one on order
    part No1527832-70/1 £73.13 + ? will let you know the out come
    barryfast ❓ 😯

    January 7, 2006 at 5:23 pm in reply to: hpt t/tub pumps #160115
    barryfast
    Participant

    Re: hpt t/tub pumps

    delta01 wrote:any one still supplying hotpoint t/tub pumps ?

    wich pump do you need wash or spin barryfast

  • Author
    Posts
Viewing 15 posts - 46 through 60 (of 69 total)
1 2 3 4 5