bigkid

Forum Replies Created

Viewing 15 posts - 31 through 45 (of 67 total)
1 2 3 4 5
  • Author
    Posts
  • November 28, 2007 at 2:31 pm in reply to: Hotpoint WT540 Fault. Overfilling & Prewash Flashing, 12 #207813
    bigkid
    Participant

    Re: Hotpoint WT540 Fault. Overfilling & Prewash Flashing

    “then eprom will have to be wrote but can only be done by us hotpoint eng.”

    Realy?
    :rotl:

    August 1, 2007 at 5:58 pm in reply to: Hotpoint WF840 #223084
    bigkid
    Participant

    Re: Hotpoint WF840

    Cheers Martin, I was of the same opinion but thought it worth a mention.
    Tony

    August 1, 2007 at 12:11 pm in reply to: Hotpoint WF840 #223082
    bigkid
    Participant

    Re: Hotpoint WF840

    I just need to know if they are interchangable electricly. Yes the terminals are different as you say but snipping off the plug and a couple of spade ends would deal with that.
    Relay is ok its the thermister terminal that is broken.
    Their resistances are similar which leads me to believe I can do a swap.
    Regards,
    Tony

    August 1, 2007 at 11:10 am in reply to: hotpoint Wma door wont open #222890
    bigkid
    Participant

    Re: hotpoint Wma door wont open

    If the door lock was clockwork it could be a wind up!! 😯

    August 1, 2007 at 11:02 am in reply to: Hotpoint WF840 #223080
    bigkid
    Participant

    Re: Hotpoint WF840

    Thanks,
    What about compatability?

    July 4, 2007 at 12:36 am in reply to: Bosch WFO2866GB/07 #219652
    bigkid
    Participant

    Re: Bosch WFO2866GB/07

    Ta Greg, not listed on this site I see.
    Tony

    July 4, 2007 at 12:25 am in reply to: Bosch WFF1201 #218862
    bigkid
    Participant

    Re: Bosch WFF1201

    Came across something similar and it turned out to be a blocked vent hose to the soap box. (pressure in drum?)
    A while back so not certain of the model.
    Tony

    May 1, 2007 at 12:21 pm in reply to: Zanussi ZWF1621 #212396
    bigkid
    Participant

    Re: Zanussi ZWF1621

    Ta Mac, it might come to that but loose a job? goes against the grain .. :rolls:

    May 1, 2007 at 12:04 pm in reply to: Zanussi ZWF1621 #212394
    bigkid
    Participant

    Re: Zanussi ZWF1621

    Thanks for that Bryan, the machine is literaly 2 weeks out of warrenty, I ‘looked’ at the com when the drum was turning and it ‘seemed’ ok although didnt take out the carbons.

    Tony

    March 28, 2007 at 4:28 pm in reply to: zanussi fc1000 Compact #209161
    bigkid
    Participant

    Re: zanussi fc1000 Compact

    Thanks Dave, you’re a gent.
    Tony

    March 28, 2007 at 2:58 pm in reply to: zanussi fc1000 Compact #209159
    bigkid
    Participant

    Re: zanussi fc1000 Compact

    I can order the part from Zanussi with the usual, “out of stock”, “don’t know when it will be in”, “non returnable”, “special order”.
    But just wondered if any of you lot out there knew of a supply that was a little less vague.
    Thanks anyway.
    Tony

    March 13, 2007 at 8:16 pm in reply to: Hoover HSE130M #207637
    bigkid
    Participant

    Re: Hoover HSE130M

    Cheers Dave, I think they are the same as Hotpoint/Zanussi.

    Tony

    March 9, 2007 at 11:57 pm in reply to: Indesit WIA121 #207157
    bigkid
    Participant

    Re: Indesit WIA121

    I think I’ll ask Tony at EMW if he has any vacancies, this looks like a good little money spinner.

    March 9, 2007 at 6:21 pm in reply to: Indesit WIA121 #207152
    bigkid
    Participant

    Re: Indesit WIA121

    Thanks Baron, but that was the problem. Turned knob to 12 o’clock and it carried on with the orig’ prog.
    Couldnt find a way to abort it.
    Unpluged for at least a minute, drained the water with a fly lead to pump. Opened door, restet a new spin prog and same again.
    Just waited till spin had finished.
    The orginal fault was that the door lock light decided to start flashing when the machine was switched off.
    If I had hair I would be pulling it out.
    Will wait to hear from customer and keep you posted.

    Tony

    March 9, 2007 at 4:24 pm in reply to: Indesit WIA121 #207148
    bigkid
    Participant

    Re: Indesit WIA121

    Ta anyway Jim, the thing went out of warrenty end of January.
    Looks like its down to Indis##t.
    Regards

    Tony

  • Author
    Posts
Viewing 15 posts - 31 through 45 (of 67 total)
1 2 3 4 5