blackandwhites

Forum Replies Created

Viewing 15 posts - 16 through 30 (of 69 total)
1 2 3 4 5
  • Author
    Posts
  • April 28, 2014 at 2:39 pm in reply to: CDA WASHING MACHINE C1370IN #412971
    blackandwhites
    Participant

    Re: CDA WASHING MACHINE C1370IN

    Thanks for you’re help.

    April 10, 2014 at 1:03 pm in reply to: White Knight 447wv #412320
    blackandwhites
    Participant

    Re: White Knight 447wv

    Might sound obvious, but the actuater pin on the door hasn’t snapped? If not,are you sure it is closing the microswitch.I have had a couple lately where door seems to shut ok ,but the micro switch was loose.
    Timers also fail on these a lot.

    January 30, 2014 at 4:55 pm in reply to: E10 on Electrolux washer/drier EWX14450W #408681
    blackandwhites
    Participant

    Re: E10 on Electrolux washer/drier EWX14450W

    I have also had broken wire to the thermistor connected to the hose at bottom of condenser causing this problem.

    January 15, 2014 at 7:55 am in reply to: MAAC LTD #407636
    blackandwhites
    Participant

    Re: MAAC LTD

    Sorry,I have just seen that there is another thread regarding this very topic.

    September 4, 2013 at 3:26 pm in reply to: servis m6011 #400282
    blackandwhites
    Participant

    Re: servis m6011

    Could be module,but it might also be open circuit pressure switch once level reached.

    August 21, 2013 at 2:41 pm in reply to: Zanussi zwd12270w 914604000 washer dryer #399664
    blackandwhites
    Participant

    Re: Zanussi zwd12270w 914604000 washer dryer

    Just a stab in the dark,but a while back I had a one like this where it was an open circuit circulating pump that was causing a very similar problem.

    February 21, 2013 at 6:29 pm in reply to: Bosch tumble dryer WTE84105GB #390601
    blackandwhites
    Participant

    Re: Bosch tumble dryer WTE84105GB

    No she has said she allows the full cycle to complete.

    February 20, 2013 at 7:55 am in reply to: beko wm5120w #390519
    blackandwhites
    Participant

    Re: beko wm5120w

    I can only think it must be either the thermistor or the wiring broken to the thermistor or heater.

    February 19, 2013 at 8:16 am in reply to: baumatic dishwasher bdi631 #390125
    blackandwhites
    Participant

    Re: baumatic dishwasher bdi631

    Think it is the same as some of the Kenwood and Matsui models.

    January 23, 2013 at 7:13 pm in reply to: Hotpoint washer dryer BWD129 #388599
    blackandwhites
    Participant

    Re: Hotpoint washer dryer BWD129

    Thanks Martin,could be,but she said if she selects normal wash without dry,machine stops at end of cycle and door wont open.

    December 19, 2012 at 5:58 pm in reply to: BOSCH SN26M830GB DISHWASHER #386538
    blackandwhites
    Participant

    Re: BOSCH SN26M830GB DISHWASHER

    Thanks,Paul.
    You were right.

    November 22, 2012 at 5:36 pm in reply to: Samsung Galaxy tab #384981
    blackandwhites
    Participant

    Re: Samsung Galaxy tab

    I have a blackberry 7 inch tablet 64g/bites From Currys £129.
    They were about £200 a few months ago.
    I use my HTC desire mobile phone as a modem when I am out and about, and it works pretty well.

    November 10, 2012 at 10:51 am in reply to: FocalPoint job offer? #384539
    blackandwhites
    Participant

    Re: FocalPoint job offer?

    I have had the same letter,and it is to become a “service agent” to repair their refridgeration products under warranty.

    I would be surprised if there would be enough work from this alone to start a new business.

    November 9, 2012 at 5:10 pm in reply to: Important Changes To Engineer Search #358921
    blackandwhites
    Participant

    Re: Important Changes To Engineer Search

    Does anybody actually get any work from the engineer search page?

    In over a year I have never had one single job.

    I have also sent all my details off when there has been “Manufacturer requires agents” topics,but again I have never received a single job.

    November 7, 2012 at 11:54 am in reply to: prima induction hob fault code e4 #384421
    blackandwhites
    Participant

    Re: prima induction hob fault code e4

    Not sure but if it is the same as a TEKA,where this means configuration error,which usually means a new induction ring is needed.
    If this is the case you will need some information on how to reconfigure the new ring once fitted,which I don’t have.

  • Author
    Posts
Viewing 15 posts - 16 through 30 (of 69 total)
1 2 3 4 5