bobnorris

Forum Replies Created

Viewing 8 posts - 31 through 38 (of 38 total)
1 2 3
  • Author
    Posts
  • February 4, 2010 at 5:15 pm in reply to: Bosch SGS69A02GB/20 #311012
    bobnorris
    Participant

    Re: Bosch SGS69A02GB/20

    Ray
    I see connect list this part as 5031687762108 or 499570.
    Cheers Bob.

    February 4, 2010 at 5:07 pm in reply to: Bosch SGS69A02GB/20 #311011
    bobnorris
    Participant

    Re: Bosch SGS69A02GB/20

    Hi Ray,
    I see this problem regularly because we’ve got hard water.This machine uses the conventional bosch pressure chamber regulater 480740 which gets blocked with crud.Also the hose leading into the sump.Take off the left side of the cabinet and observe the sludge.remove both parts and clean out.The customer wont believe how much better it washes with a decent water level!
    Haaapy Days. Bob

    November 28, 2009 at 8:17 pm in reply to: AEG 66600 E60 Fault code #304693
    bobnorris
    Participant

    I’d never have guessed the answer to this one.The wall socket was burning up and dropping the voltage to the machine. Fitted new plug and plugged in another socket and hey presto.Thanks for the advice on the fault codes dave.
    Cheers bob.

    December 24, 2006 at 4:59 pm in reply to: Zanussi Dishasher fault – DE6744 – 91188011/01 #185967
    bobnorris
    Participant

    Re: Zanussi Dishasher fault – DE6744 – 91188011/01

    Hi grooster.Ive got the same dishwasher DE6744 with the same fault! Changed the motor impellers, IWMS and pressure switch so far.Now at wits end. Did you ever crack the problem? Happy new year.Bob

    January 26, 2006 at 9:54 am in reply to: A E G dishwasher F40640W wont heat #162203
    bobnorris
    Participant

    Re: A E G dishwasher F40640W wont heat

    Dave,The PNC is 911 232601 01, The dishwasher is 2 years old.Hope this helps. Cheers Bob.

    January 19, 2006 at 10:40 pm in reply to: BEKO WMA 1715S washing machine.WONT PROGRAMME. #160500
    bobnorris
    Participant

    Re: BEKO WMA 1715S washing machine.WONT PROGRAMME.

    Thanks Chris. This customer doesnt want to spend more than £75 on the machine so its bye-bye to this one. C Cheers Bob.

    December 7, 2005 at 10:55 pm in reply to: Microwave Saisho MW2000 Turntable Motor Required #156959
    bobnorris
    Participant

    Re: Microwave Saisho MW2000 Turntable Motor Required

    Hi Laurence, I`ve got a motor from a Matsui 170 TC.It`s similar but the length of the shaft above the base is only 18mm.The rollpin seems to be in the right place.Perhaps the drive-bush is long enough to engage?

    October 5, 2005 at 8:15 am in reply to: Smeg Dishwasher DW1612C Error Code? #148918
    bobnorris
    Participant

    laurenceuk wrote:Hi,

    Thanks for everyones help with this.

    According the LED error code, it certainly looks like a reset procedure due to a power surge or some-such-like (E7), is looking for a flow meter which is not fitted and defaulted to factory setting.

    I will keep you posted on its outcome.

    Laurence

    Hi laurence, Try reducing the fill rate to a slow trickle.If this works then its probably a blocked inlet tract into the sump .Remove the filling chamber and scrape out the sludge.The back-up of water is causing the pressure switch to operate and bring in the drain pump.

  • Author
    Posts
Viewing 8 posts - 31 through 38 (of 38 total)
1 2 3