[bobnorris]

Re: Maytag MAV9750AGW Top Loader NoSpin

I havent stripped anything to find out.I’m looking on http://www.partadvantage.com at a transmission diagram.Do you know what part reference to look for? Bear in mind the wash agitation is normal.

[bobnorris]

Re: Whirlpool ADG7470/1 Int/dw No fill

I’ve just checked the price of a new module from
Connect, its £120.44+vat part no 480140102618.Has anyone had to replace this part and will it cure the fault? Any feedback appreciated.

[bobnorris]

Re: Whirlpool ADG7470/1 Int/dw No fill

Yes it does have a flowmeter tank and i’ve checked the connection by sliding the plug on and off. The problem is its stuck in fault code mode and i cant get out.Heeelp ❓ ❓ 😕

[bobnorris]

Re: Whirlpool ADG7470/1 Int/dw No fill

Just been back to check this machine and confirmed the fault light flashes 8 times, then rest for a few seconds and repeats 8 flashes.This goes on forever and i cant get out of this mode to set a programme.I press and hold button and the light goes out but returns after a short pause.I think i may have pressed something and got stuck in diagnostic mode.I see on older models that 8 flashes means water level failure, which was the original problem with this machine i.e. no fill.

[bobnorris]

Re: AEG L88810 Tub change.

I’ve often managed to get the zanussi ones out using a cold chisel and hammer.I know it sounds brutal but if the head is countersunk the taper is tight and needs a good belt.Whatever happened to proper engineering?

[bobnorris]

Re: Diplomat oven AHY4410 grill regulator

Luckily thats an easy one Steve.P1-4-2-S2 are all like for like and you need an extra link from P1 to S1 to feed live to the pilot switch.
Cheers Bob

[bobnorris]

Re: AEG WASHER DRYER L12830 Fault code E20

Thanks a bunch Martin,the customer has been on holiday for weeks!!The condenser was blocked to the eyeballs but you cant see that till you strip the cabinet,not always easy.Now working perfectly.Its great we can share our knowledge,top man.

[bobnorris]

Re: AEG WASHER DRYER L12830 Fault code E20

My email.
robertjamesnorris@hotmail.com The workshop manual would be very helpful.
Thanks Dave

[bobnorris]

Re: Smeg DWF64

These are probably the normal smeg O rings that i’ve used many times on smeg and diplomat.Part number is SMG754131307, around £3 each from Connect Distribution(Electrue),daylight robbery.
Cheers Bob.

[bobnorris]

Re: Miele Dishwasher

The first thing i checked Steve.The sump is empty and the impeller is free. Ive got to say i didnt check the winding for continuity cause ive never seen one fail.Would this stop the machine from starting?

[bobnorris]

Re: Creda condenser tumble dryer T632CW intermittent heat

Thanks Jim.I fitted a new board 1702391 and runs perfectly but couldnt see any dry joints .Reckon it must be a faulty relay.
Cheers Bob

[bobnorris]

Re: Smeg Dishwasher DWI 612

Spot on.The old valve was leaking.Regards Bob

[bobnorris]

Re: Smeg DWI 612 Integrated Dishwasher

Thanks a lot johnsdad.The alternate valve showed signs of leaking.A new one did the trick.
Bob

[bobnorris]

Re: Smeg DWI 612 Integrated Dishwasher

What exactly is an alternate valve,is it a regen valve?

[bobnorris]

Re: Bosch SGS69A02GB/20

Paul’s spot on.Just as a bit more help,you have to remove the large fill/empty vessel on the left first and have a bowl ready to catch the water which will pour out .
Bob

[Author]

Posts