clockworkone

Forum Replies Created

Viewing 15 posts - 196 through 210 (of 555 total)
1 2 3 … 13 14 15 … 35 36 37
  • Author
    Posts
  • August 25, 2014 at 11:08 am in reply to: Dyson Dc16 handheld vac #418039
    clockworkone
    Participant

    Re: Dyson Dc16 handheld vac

    Thank you Spiderpig. Have connected multimeter up to it and pressed switch. There was no drop in voltage when it shut down.Have taken a chance and ordered motor body.

    August 21, 2014 at 4:56 pm in reply to: samsung d/washer #418152
    clockworkone
    Participant

    Re: samsung d/washer

    Flooded base antiflood activated.Emptied out water and ran machine until d14 appeared.Machine has seriously overfilled.What system do these use for level ie flow meter,reg pr sw.Cant find anything in on spares site.

    August 19, 2014 at 5:36 pm in reply to: Dyson Dc16 handheld vac #418037
    clockworkone
    Participant

    Re: Dyson Dc16 handheld vac

    Thank you Muv.Tried larger magnet to no avail.Looks like its soldering iron and good glasses.

    August 19, 2014 at 10:53 am in reply to: Dyson Dc16 handheld vac #418035
    clockworkone
    Participant

    Re: Dyson Dc16 handheld vac

    Thank you Don.Yes I tried it without filters.No difference.I thought about a motor toc but it runs so little it would hardly overheat that quickly.Also it will start straight away again.Battery showing 24.7v.

    August 18, 2014 at 1:39 pm in reply to: aqxxf149pm dampers #418005
    clockworkone
    Participant

    Re: aqxxf149pm dampers

    Thank you very much Andy.

    August 15, 2014 at 9:03 am in reply to: adg7440 #417866
    clockworkone
    Participant

    Re: adg7440

    Thanks for that Dave.

    July 29, 2014 at 8:23 am in reply to: belling oven hinges #417239
    clockworkone
    Participant

    Re: belling oven hinges

    Thank you Tell.

    July 4, 2014 at 10:40 am in reply to: Delmore spares #416210
    clockworkone
    Participant

    Re: Delmore spares

    Thank you Don.I didnt think this one would be easy. luckily this oven is local so i will measure it.I think this is a kitchen fitters supply.Paul

    June 8, 2014 at 4:37 pm in reply to: candy wash motor #415003
    clockworkone
    Participant

    Re: candy wash motor

    Thanks Martin.That is the motor fitted.When 91200502 is typed into connect it shows motor with black pump with bayonet fitting.I guess its an alternative replacement part.Paul

    June 5, 2014 at 8:51 pm in reply to: w/pool 3rlsq8033rwd #414854
    clockworkone
    Participant

    Re: w/pool 3rlsq8033rwd

    Many thanks.

    June 4, 2014 at 1:49 pm in reply to: pcb part no #414827
    clockworkone
    Participant

    Re: pcb part no

    Thank you appreciate that.

    May 16, 2014 at 8:16 am in reply to: wf620 board #413769
    clockworkone
    Participant

    Re: wf620 board

    Thanks Martin.

    May 12, 2014 at 3:06 pm in reply to: Connect. Opened module #413592
    clockworkone
    Participant

    Re: Connect. Opened module

    And worst of all this job is at the limit of where i travel.Really not happy with secondhand parts.

    April 28, 2014 at 8:50 pm in reply to: 680uf capacitors #412908
    clockworkone
    Participant

    Re: 680uf capacitors

    Thank you Dave.

    April 28, 2014 at 8:48 pm in reply to: Indesit Wil103 dead #412899
    clockworkone
    Participant

    Re: Indesit Wil103 dead

    HotDog.. Many thanks for that.

  • Author
    Posts
Viewing 15 posts - 196 through 210 (of 555 total)
1 2 3 … 13 14 15 … 35 36 37