clockworkone

Forum Replies Created

Viewing 15 posts - 211 through 225 (of 555 total)
1 2 3 … 14 15 16 … 35 36 37
  • Author
    Posts
  • April 23, 2014 at 4:06 pm in reply to: Zanussi ff thermostat #412772
    clockworkone
    Participant

    Re: Zanussi ff thermostat

    Don.There is no other digits after pnc. Only other detail is a type no which is b 23753.Thanks Paul

    April 15, 2014 at 6:34 pm in reply to: bfi620 #412457
    clockworkone
    Participant

    Re: bfi620

    Much obliged Jim.Thank you

    April 12, 2014 at 8:40 am in reply to: beko wash motor #412352
    clockworkone
    Participant

    Re: beko wash motor

    Thank you Dave.

    April 11, 2014 at 2:38 pm in reply to: samsung oven #412354
    clockworkone
    Participant

    Re: samsung oven

    Thank you Dave for reply.I believe there is more than 3 pins in red plug.I think the version that needed new loom etc was type00.That is only version with footnote about change in connect website.This one has 01 in box after mod no on name plate, so hoping it is updated version.Thanks again.Paul

    March 28, 2014 at 8:42 pm in reply to: akz 515 ix oven #411758
    clockworkone
    Participant

    Re: akz 515 ix oven

    Grendal.Many thanks for that.Paul

    March 28, 2014 at 3:40 pm in reply to: akz 515 ix oven #411756
    clockworkone
    Participant

    Re: akz 515 ix oven

    service no 858551515010. Had a look today,comes on for approx 90 seconds and then f03 appears.Main oven shuts down. Temp probe giving a reading of 1058 ohms. Anyone had much experience with these.I believe power board should be replaced but just want to check that i havnt missed anything.

    March 18, 2014 at 9:03 pm in reply to: Whirlpool regulator #411112
    clockworkone
    Participant

    Re: Whirlpool regulator

    Many thanks Dave.

    March 2, 2014 at 1:13 pm in reply to: matsui mf2s/a #410466
    clockworkone
    Participant

    Re: matsui mf2s/a

    Thank you Martin. Dont get many of these over here.

    February 17, 2014 at 9:10 am in reply to: Baumatic t/dryer #409611
    clockworkone
    Participant

    Re: Baumatic t/dryer

    Many thanks for that info Steve.Paul

    January 21, 2014 at 9:07 pm in reply to: matsui mf2s/a #408051
    clockworkone
    Participant

    Re: matsui mf2s/a

    Many thanks Martin.

    December 13, 2013 at 9:53 am in reply to: hotpoint 9605 #406180
    clockworkone
    Participant

    Re: hotpoint 9605

    Many thanks Martin,Jim and Andy.That gives me something to go on now.Kitchen was built around washing machine so new front loader would be too wide a fit.Thanks again.Paul

    December 5, 2013 at 9:41 am in reply to: sy36 oven #405780
    clockworkone
    Participant

    Re: sy36 oven

    Many thanks for all your’e replies.Sounds like t/limiter fault but will check connector box as well..paul

    December 2, 2013 at 12:02 pm in reply to: 9605 top loader #405365
    clockworkone
    Participant

    Re: 9605 top loader

    Clutch it was..Obsolete at connect and m/part.Ukwhitegoods came up trumps.paul

    December 1, 2013 at 8:01 pm in reply to: 9605 top loader #405363
    clockworkone
    Participant

    Re: 9605 top loader

    Many thanks for replies.Most certainly very useful advice.Any idea who still stocks these clutches.Paul

    November 25, 2013 at 6:47 pm in reply to: adg644 d/w #405170
    clockworkone
    Participant

    Re: adg644 d/w

    Thank you Deltra. Should have said that I cleared e7. Cleaned reed sw connections. No fault codes showing now.cust says it seems stuck on drying mode.I suspect it may still be stuck on wash program.Did not look when there but suspect if glass owi fitted that it may be dirty.

  • Author
    Posts
Viewing 15 posts - 211 through 225 (of 555 total)
1 2 3 … 14 15 16 … 35 36 37