[clockworkone]

Re: help electrolux oven eso pmss

landlord decided to scrap machine. fitted new oven for him yesterday.

[clockworkone]

Re: heater element removal

thanks for that martin it was a wm machine. i had a look to see had i a new element. only when i realised i had not did i change tactics.thanks again

[clockworkone]

Re: help electrolux oven eso pmss

thanks mike,gandh1 for the good advice.went into rental agency this morning and told them that it was impossible to diagnose power board without programmer working,explained that i would have to give them two quotes and that if programmer rectifies problem all good and well but if not they were commited to carrying out power board replacement. i said i am not willing to be liable for cost of parts if they pull out half way through job. they accepted these terms.

[clockworkone]

Re: help electrolux oven eso pmss

p/n 949711720. looking for a bit of reassurance on this one before i order programmer.symptoms are no display,evidence of spillage on programmer board,bleep can be heard.tested every thing else power to controller.obviously no fault codes so no way of proving whether any other faults lie in main power board. both programmer and power board expensive and non returnable. supplier has never supplied one of these previously. thinking of writing this one off as too much money for a single oven. dont want to get caught.paul

[clockworkone]

Re: help electrolux oven eso pmss

hi the switch is mechanically operated on the lock itself.to be honest am not too familliar with this model myself.tds info very good in fault finding.been out to this one this morn and determined it is the control board that is faulty.checked all stats and elem.looks like some kind of spillage has made its way onto board.checked res at supply and showing(according to tds) that it is the control and not power board. cut off switch on wall by passed so should have walked away but it was rental agency who can supply a bit of work to me. have told them

[clockworkone]

Re: help electrolux oven eso pmss

had a think about this on and was wondering could it be caused by faulty door lock due to it being a pyro oven. had a look on w/diag and showing micro sw on lock.paul

[clockworkone]

Re: help electrolux oven eso pmss

thanks mike, looks like a recycling job then.not worth throwing that kind of money at a single oven. thought possible safety stat but its the total lack of display thats worrying me will have a look sat anyway.thanks again.paul

[clockworkone]

Re: help electrolux oven eso pmss

its come through a rental agency all i have is model no and serial no 44606229

[clockworkone]

Re: hotpoint fdw60

thanks for that, job done new jubilee clips fitted

[clockworkone]

Re: hotpoint wma 52 bearings

thanks allsorts, guess its one for recycling.when enroute to a job tomorrow will have a quick look just in case it motor bearing.thanks again.paul

[clockworkone]

Re: creda simplicity w100fw drum bearings

thanks very much dave,its a bit of a trek to this one and trying to avoid a return visit. paul

[clockworkone]

Re: hotpoint d/w fdw60 error code lights 4 and6

thanks for that, think you are right. is there a reprogramming procedure with these or is it just straight swop.p

[clockworkone]

Re: zanussi zdt 6053 not heating

mike your diagnosis spot on, faulty relay on pcb.any advice on where to buy said relay. thanks again,paul

[clockworkone]

Re: zanussi zdt 6053 not heating

hi mike thanks for tip on pcb,had a look and can see no signs of damage on board.tested ntc from module and got reading of 3810ohms at 20c.service manual shows 4850 at 25c, is this reading within tolerance.gratefull for all advice and tips.regards paul

[clockworkone]

Re: solid hotpoint and indesit plastic drums

many thanks for that info Jim.all these tips help a lot at this stage. regards paul

[Author]

Posts