[clockworkone]

Re: hotpoint w/dryer loose top weight

thank you all for your contributions(serious and not so serious) but as mike says its a little more interesting than the run of the mill stuff and keeps the brain occupied for a while anyhow. customer totally understands that there is no way i can guarantee that it will last and is willing to pay for me to try this.otherwise its a complete new outer drum for machine.i know which option i would try if it was my machine.i suppose there is always super glue(people that know me will understand this one)paul

[clockworkone]

Re: Zanussi ZDT 6053

have got this dw myself,same symptoms as described by you,will fail to heat at all soon.soldered in new relay works a treat now. paul

[clockworkone]

Re: Zan ZWF14070W1 914226103(00)

check inlet solenoids, especially pre wash had a 12070w(2 yr old) go down on this.replaced solenoids but still no joy.triac on board gone.paul

[clockworkone]

Re: hotpoint oven sy36k wiring diagram

went out to this oven today. fault was display only.checked stats and elements. everything there fine. have put it down to relay on timer pcb faulty.if you give it a slight tap oven comes on and arcing can be seen in relay.is this a straight swop of timer or can relay be replaced.paul

[clockworkone]

Re: hotpoint oven sy36k wiring diagram

many thanks bob, have sent you a pm

[clockworkone]

Re: hotpoint few 10p advice please

thanks for the info jim, it belongs to an elderly couple who thankfully are not too far away from me.i will pop in on mon and have a quick look at it.paul

[clockworkone]

Re: wae24162 poor wash results

sorry have edited question

[clockworkone]

Re: zan iz12 bearing change

thank you seamy,iadom and mike.i appreciate all your advice.paul

[clockworkone]

Re: masterpart deliveries on go slow

traced order today. ordered last fri morn, can pick up usually at local courier depot sat afternoon.as of today(tues) still at courier depot in Droitwich. order before that also late. it must just be an overseas issue.

[clockworkone]

Re: Zanussi Dishwasher

cornflakes did you manage to get the sw for this d/w.have to replace relay on one that has sw stuck in on position. i know theres allways the socket to turn it off but while its out may as well do it.do you have a part no.regards paul

[clockworkone]

Re: zan zwf12070w

thanks mike,good advice. i took brushes out like new with no obvious signs of condensation though i will say m/c in shed attached to house and had to move tool box to stop drip getting to it,whether it has previously done damage and was dry when i had a look.ins readings well above 40. also when m/c put on rinse it turns drum but no water intake thanks again.paul

[clockworkone]

Re: zan zwf12070w

ran diagnostics on m/c today( e11 diff in filling during wash phase) swopped inlet valve and pr sw. drain hose outlet a little bit high but has worked for 2 yrs.when lowered no diff. did all other checks ie motor, pump,heater(ins and res) pr sw bottle and tube and interlock. machine drains for a few sec at start then nothing.customer getting rid of m/c.to make my day have another to look at tomorrow dressed up as a tri bendix.will have to try and get connect ac to get tech info.thanks again everyone.paul

[clockworkone]

Re: zan zwf12070w

thanks gandh1, its a bit of a chain reaction this one. was hoping the fact m/c responds to me manually triggering pr sw was a sign that i might be at the end of the line with this one. maybe not

[clockworkone]

Re: zan zwf12070w

thanks for all the advice,yes the reading was infinity on valve solenoid.the pr sw took quite a bit of blowing or sucking to do anything.it seemed very very sluggish compared to reg pr sw is this normal. will run diagnostics on tues.thanks again.p

[clockworkone]

Re: hotpoint wf440p dead

thanks to both of you for that info. lady has since told me that machine got wet a while back and worked on and off for a while so maybe it could be programmer connections fault as you mentioned.thanks again.paul

[Author]

Posts