[DDA]

Re: Whirlpool Dishwasher ADG7560/2 just keeps pumping out.

Dose the machine display any error codes (count the flashing lights before the pause or may be shown as a numerical display).

Then look up the codes to work out what the fault may be.

http://www.ukwhitegoods.co.uk/help/faul … codes.html

Reply back if you are still stuck.

Anthony

[DDA]

Re: Whirlpool Dishwasher ADG7560/2 just keeps pumping out.

No problem Subs, thanks for the advise in return.
Anthony

[DDA]

Re: Whirlpool Dishwasher ADG7560/2 just keeps pumping out.

I have had issues with these machines having faults on the flow meter witch is part of the air brake on the left hand side. 481241868368.it measures the amount of water flowing into the dishwasher instead of the pressure created by water in the sump.

Bosch machines had a similar issue but the flow meter was a separate cheap part.

Remove the side panel and check if the valve is letting water through the flow meter whilst pumping. If it is, I would try the replacing airbrake chamber. You can get the Contact Reeds for the flow meter 481231019147 (included in the airbrake) but when I have tried these in the past they didn’t work, they are the cheaper option to try though.

If there is no water flowing then I would start to check the valve and the connections to it as, as far as I am aware, the dishwasher will only progress from the initial pumping once it has detected the water flowing through the flow meter and it can safely measure the water flowing into the machine.

Hope this is a help.
Anthony

[DDA]

Re: rs20 and the rs21 defrost sensor

cheers bob,
advice much appreciated
Anthony

[DDA]

Re: samsung RS20CCMS evap iceing up

no problem thanks for the advice.
I have also just found the fault codes on the Samsung unit on the public side of ukw. Ill double check all the faults.

[DDA]

Re: service manuals

Thanks martin,
Always appreciate the advice.

[DDA]

Re: samsung RS20CCMS evap iceing up

Dose anyone know if there are any service manuals for this fridge available.

[DDA]

Re: service manuals

connect seems to be taking manuals of the mediator and just leaving a lot of models with just part diagrams.

[DDA]

Re: indesit idl10suk.c 6440685 not heating

thanks for the advice
appreciated

[DDA]

Re: indesit idl10suk.c 6440685 not heating

The element has 240v to both terminals the element. tested using a multimeter.

The dishwasher has been plugged into a socket with no earth connection, didn’t know if this could cause any common pcb issues.

[DDA]

Re: Lamona lan8652 – 7619333871 cant change sottener setting

thank you Dave, i will let you know how i get on.

[DDA]

Re: fisher pykel ds603h dripimg / leaking

i have run the units there is no leaks that i can see from the dispenser and softener units at the front and i cant see any internal component leaks. it seems that the lid for the tank is not always closing on either side. the motors are running but not bring the threaded pin down at the bottom of the motor. is this a known issue and am i looking at new motors or other parts

thanks for all the advice

[DDA]

Re: Beko Frige Freezer CDF64S overfreezing

I have a number of issues with the beko units. i have changed 5 sets of pcb’s (small control and main rear board)and have had no success. there is a thermistor in the evap in the freezer but is sealed into the insulation and cant remove, also cant find the details for the part (not visible in the diagram. can anyone shed any light on this issue as is extremely common.

[DDA]

Re: A return of the BAD old days

Andy jones wrote:I know these lux fan motors are supposed to be low speed motors perhaps someone will say why

haven’t had any issues since fitting the alternative motor (about 6 years) but always option to suggestions.

[DDA]

Re: SIMPLE PCB REPAIR TIPS

I have a diplomat adp8234 PCB not heating. no power to the coil on the relay. any advice.

[Author]

Posts