DDDave

Forum Replies Created

Viewing 15 posts - 46 through 60 (of 212 total)
1 2 3 4 5 … 13 14 15
  • Author
    Posts
  • July 10, 2014 at 10:11 pm in reply to: Zanussi ZDF511 #416525
    DDDave
    Participant

    Re: Zanussi ZDF511

    Perfect, thanks Martin.

    May 1, 2014 at 7:32 am in reply to: Zanussi ZWD12270W1 Wiring #413104
    DDDave
    Participant

    Re: Zanussi ZWD12270W1 Wiring

    Excellent.

    Thanks very much Jem.

    April 30, 2014 at 10:18 pm in reply to: Neff S54T59 #412067
    DDDave
    Participant

    Re: Neff S54T59

    Sorry,I should have reported back sooner. I cleaned and tightened all connections with no success, so I fitted a new module and that sorted the problem. Thanks for the help.

    April 9, 2014 at 12:42 pm in reply to: Neff S54T59 #412066
    DDDave
    Participant

    Re: Neff S54T59

    Thanks Martin.

    Will check and report.

    Dave

    April 9, 2014 at 7:23 am in reply to: Neff S54T59 #412064
    DDDave
    Participant

    Re: Neff S54T59

    Hi Martin,

    thanks for the reply.

    More numbers – S54T59X0GB/10, FD 8704, Type – SD11XT1F

    Any good ?

    Dave

    January 3, 2014 at 11:46 pm in reply to: Tips, Tricks & Shortcuts #290428
    DDDave
    Participant

    Re: Tips, Tricks & Shortcuts

    mjjuk wrote:
    Rather than break the handle unscrew the lid and reach inside and push over the latch from the inside

    If the handle is broken ,the door locked and the machine integrated then this is the quickest way I have found to open it.

    August 21, 2013 at 4:23 pm in reply to: Leisure DWLT 65 #399415
    DDDave
    Participant

    Re: Leisure DWLT 65

    captaincaveman1 wrote:This is actually a Beko dishwasher so it could be the water counter at fault its located between the valve and the side tank on the left side. They are known for giving filling problems.

    I thought of that but the Beko normaly fills and then stops but this does not fill at all.

    August 21, 2013 at 4:21 pm in reply to: Leisure DWLT 65 #399414
    DDDave
    Participant

    Re: Leisure DWLT 65

    Criscold wrote:Did you receive the mail I sent last week as this was attached

    Colin
    Hi Chris,

    I didnt receive that email. Could you resend please.

    Thanks.

    Dave

    August 20, 2013 at 8:58 pm in reply to: Leisure DWLT 65 #399411
    DDDave
    Participant

    Re: Leisure DWLT 65

    I am still having problems with this. I replaced the float switch just in case but its still the same. I have noticed however that after it drain pumps at the start , if I flick the float switch a few times then it fills and washes. It doesn’t complete the cycle though. Does anyone have a test procedure for it PLEASE.

    August 14, 2013 at 8:36 pm in reply to: Leisure DWLT 65 #399410
    DDDave
    Participant

    Re: Leisure DWLT 65

    Thanks, PM sent.

    August 14, 2013 at 8:35 pm in reply to: Old Hoover dryer D6150 not turning #399434
    DDDave
    Participant

    Re: Old Hoover dryer D6150 not turning

    There is a cut-out in those motors and they fail. The old twin tub used the same coil but without the cut-out. Check that the motor is clean and oil its bearings. Also check the front drum bearings to make sure the drum is free to turn. If its still cutting out then the motor is faulty.

    August 14, 2013 at 4:58 pm in reply to: Leisure DWLT 65 #399408
    DDDave
    Participant

    Re: Leisure DWLT 65

    Switch tests ok. Any other ideas please ??

    August 14, 2013 at 1:19 pm in reply to: Leisure DWLT 65 #399407
    DDDave
    Participant

    Re: Leisure DWLT 65

    Will do. Thanks.

    July 20, 2013 at 10:43 am in reply to: Whats this ? De Detrich oven. #397952
    DDDave
    Participant

    Re: Whats this ? De Detrich oven.

    Thanks Captain.
    The stat is O/C so then I suppose its an overheat stat. I just wanted to know what its function was. I don’t think there is anything wrong other than the element.
    Cheers.

    June 21, 2013 at 10:11 pm in reply to: Bosch. Is this a fault code ? #396678
    DDDave
    Participant

    Re: Bosch. Is this a fault code ?

    Thanks again Paul. I will try that on Monday.

  • Author
    Posts
Viewing 15 posts - 46 through 60 (of 212 total)
1 2 3 4 5 … 13 14 15