Forum Replies Created
-
Posts
-
Re: Neff Double oven
Hi merv
Have you had this b4 seems a bit excessive if a lamp could do that much damage.zanussi dishwasher codes
Zanussi Dishwasher Codes:
Codice Leds
SAFETY DEVICE POSSIBLE CAUSES
WATER FILL TIME-OUT
The correct level is not reached.
The pressure switch does not
switch to FULL (1-3) within 4
minutes after activation of the
solenoid valve[AL 5] [LD9]PRESSURE SWITCH ON “EMPTY” (1-2) When the level has been reached, the pressure switch does not
return to 1-3 within the maximum time of 60 secondsc
a) The tap on the fill hose is closed.
b) Mains water pressure <3 bar.
c) The anti-flooding device has intervened.
d) Fill solenoid/connections disconnected.
e) Pressure switch faulty/Loose connections.
f) Obstructions / Leakage from the tube connecting the
IWMS to the pressure switch.
g) Central filter clogged.
h) Excessive foam.
i) Dishes upside-down.
j) Siphon effect in drain hose.AL 6] [LD10] DRAIN TIME-OUT
a) Domestic drain unsuitable (blocked)
b) Motor faulty (pump unit / drain impeller)
c) Pressure switch faulty (blocked on 1-3)
d) Obstruction in connection between IWMS and
pressure switch
e) Obstruction in tube between IWMS and sump
f) Control board (relay interrupted)[AL 4] [LD9] +[LD10]
INTERVENTION OF ANTIFLOODING
DEVICE
a) Leakage from the various connections
b) Floating sensor blocked mechanically
c) Float microswitch faulty
*) [AL 3] [LD11]
WATER HEATING TIMEOUT
The correct temperature is not
reached within 45 minutes after the
heating element switches on
a) Heating element interrupted
b) Safety thermostat open
c) Electrical connections interrupted / loose
d) NTC sensor faulty / Poor thermal contact
e) Insufficient water circulation in tub
f) Motor faulty (pump unit / washing impeller)
NTC SENSOR SHORTCIRCUITED
Range < 450 Ω
a) Temperature sensor faulty (short-circuited)
b) Electrical connections short-circuited
*) [AL 1/2] c) Temperature too high (>90°C) [LD9] +
[LD11] NTC SENSOR OPEN
Range > 26.700 Ω
a) Temperature sensor faulty (open)
b) Electrical connections interrupted/disconnected
c) Temperature too low (< -10ºC )[AL 7] [LD10] +[LD11] MOTOR INOPERATIVE
a) Motor winding interrupted/short-circuited
b) Electrical connections loose / interrupted
c) Motor jammed (foreign bodies/pump unit)
d) Tachymetric sensor interrupted/short-circuited[AL 8][LD9] +[LD10] +[LD11]MOTOR TRIAC SHORTCIRCUITED
a) Control board (Triac short-circuited)
In alarm conditions – [AL4], [AL5], [AL6], [AL7], [AL8] Dishwasher stopped – the corresponding LEDs flash
To cancel the alarm condition Press (S0) to switch the dishwasher off.
When the dishwasher is switched on again The cycle resumes from the point at which it was interrupted.
*) In alarm conditions – [AL1/2], [AL3] ] The cycle is completed, and no alarm is displayed to the user; the
condition is simply stored in memory for inspectionRe: Zanussi ZX99/5SI
Three lights flashing is normaly the sensors. in the freezer quite a tricky job to change. probly best to get engineer in.
Re: Zanussi DX6453 heating problem
Two things it can be dry joint on pcb heater relay or heater itself. Can sometimes resolder the joint but in most cases the pcb has to be changed. Between £50 -90. power off if investigating
Re: electrolux EW 1200 1 drum not spinning
I disagree if you can here the motor but the drum doesn’t turn then its most likey the belt dont you think penquin.
Re: Zanussi Aquacycle F1245W
does the machine try to spin about three times the click off if it does it the timer part number 1320558107. hope this helps. its easy to change. repaly back and i will help you power off if trying
