evo1

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 34 total)
  • Author
    Posts
  • in reply to: Bek o dsfn1530b console #453481
    evo1
    Participant

    Re: Bek o dsfn1530b console

    Many thanks for the info kai

    in reply to: Bek o dsfn1530b console #453479
    evo1
    Participant

    Re: Bek o dsfn1530b console

    Hi yes I thanks for the reply. What do you mean by the buttons are different in the new console? Cheers

    in reply to: Hotpoint FF175BP fridge too warm #322320
    evo1
    Participant

    Re: Hotpoint FF175BP fridge too warm

    STILL NEED HEATER KIT ,AS ORIGINAL NOT UP TO THE JOB :rolls:

    in reply to: Fridgemaster MTRL130 #111865
    evo1
    Participant

    Re: Fridgemaster MTRL130

    bit confused here, this is a single door fridge isnt vt9 a fridge freezer stat?

    in reply to: IDL 535 Indesit Dishwasher/ No Heat #300364
    evo1
    Participant

    Re: IDL 535 Indesit Dishwasher/ No Heat

    no rear stat on that model, just order board

    in reply to: ignis 348 motor and press switch #300335
    evo1
    Participant

    Re: ignis 348 motor and press switch

    cheers electofix, any ideas on pressure switch number, it was leaking, removed it, took it apart cleaned out fat deposits, but was still leaking, although not as bad, can I fit 481227128556 switch? that the only number I’ve found so far (whirlpool)

    anyone help? 💡

    in reply to: posting dates #290959
    evo1
    Participant

    Re: posting dates

    nope tried on internet explorer, (use google chrome mostly) still cant see time/date, but could see it untill I logged in ❓ ❓

    in reply to: re bearings on an Indesit WD 12 S UK #289778
    evo1
    Participant

    Re: re bearings on an Indesit WD 12 S UK

    wack with copper mallet will loosen threadlock ❗

    in reply to: hotpoint larder fridrge #288570
    evo1
    Participant

    Re: hotpoint larder fridrge

    push on liner at the back, make sure its not loose or creasing at the corners, liner failure common, phial comes adrift from correct position….unrepairable

    in reply to: WD440 Blowing dryer elements! #288409
    evo1
    Participant

    Re: WD440 Blowing dryer elements!

    yep common problem, just check its not connected to hot and cold, if it should be cold fill only,grey hose with y piece.

    in reply to: Hotpoint Condenser Tumble Dryer tripping #287398
    evo1
    Participant

    Re: Hotpoint Condenser Tumble Dryer tripping

    depending on where the machine is (ie flooring), just drill a 3mm hole at the lowest point, and glue some dense foam on the outside over the top off the hole, like a foam nappy, also check that the hole in the wall if they had a vented machine is sealed off, filled in or blocked, as cold air coming through that and hitting the rear cover will cause your problem as any moist air inside the cover will condensate, turn to water and trip the heater

    in reply to: Indesit H20 #287889
    evo1
    Participant

    Re: Indesit H20

    either tap off or valve failure……

    in reply to: hotpoint rla33 thermostat #286632
    evo1
    Participant

    Re: hotpoint rla33 thermostat

    feel the liner at the back, will be loose, you can push it in……..write off

    in reply to: How the ****did that get in there #285295
    evo1
    Participant

    Re: How the ****did that get in there

    best ones are the condoms in the pumps, especially when the lady of the house has been on the pill for years 😛 😛 😛
    love advising them they’re one use only and should not be washed and reused 😉 😉 😉

    in reply to: Strange WD440 fault #283809
    evo1
    Participant

    Re: Strange WD440 fault

    for some strange reason these wd’s kind of get a corrupted programme, if you put it on wash they hardly tumble, usually cured by reprogramming eeprom… hope that helps

Viewing 15 posts - 1 through 15 (of 34 total)