gegsy

Forum Replies Created

Viewing 15 posts - 1,666 through 1,680 (of 6,724 total)
1 2 3 … 111 112 113 … 447 448 449
  • Author
    Posts
  • September 27, 2007 at 5:48 pm in reply to: Sharp R774M microwave problems #228708
    gegsy
    Participant

    Re: Sharp R774M microwave problems

    Hi
    Sorry wasn’t trying to be unhelpful, just safe 😉
    The list of reasons why its not generating microwaves is quite long and to list them would be pointless as it would mean you have to open the case and measure components; then we are back to the high voltage scenario again :rolls:

    Greg

    September 27, 2007 at 5:44 pm in reply to: Bosch WFK2200 My bleep’s come back #227376
    gegsy
    Participant

    Re: Bosch WFK2200 My bleep’s come back

    Hi
    If it aint in the manual its not a user selection 😉 .
    If its only the bleep playing up I wouldn’t worry as the only solution would be to change the PCB/module (it aint cheap) 🙂

    Greg

    September 27, 2007 at 8:09 am in reply to: Fault – My dishwasher keeps tripping RCD #228720
    gegsy
    Participant

    Re: Fault – My dishwasher keeps tripping RCD

    Think I will ask Adam Hornsby 😆 you lot are hopeless 😛

    Greg

    September 26, 2007 at 8:53 pm in reply to: Sharp R774M microwave problems #228706
    gegsy
    Participant

    Re: Sharp R774M microwave problems

    Hi
    Due to the dangerous voltages that are within even when powered down, I must refer you to pro help.
    Please use the link below to find a suitable engineer in your area.

    Greg

    September 25, 2007 at 8:59 pm in reply to: Noisey Bosch Frost Free Fridge-freezer #228641
    gegsy
    Participant

    Re: Noisey Bosch Frost Free Fridge-freezer

    These are the dogs doo dahs IMHO when it comes to their refrigeration.
    Have you tried pulling appliance away from the wall incase compressor is knocking on skirting board etc?

    As fara s fan, it may be ice bulid up hitting the fan or some packaging entering the fan assembly (poss overloading)

    Greg

    September 25, 2007 at 8:27 pm in reply to: Diplomat apl 1304 #228640
    gegsy
    Participant

    Re: Diplomat apl 1304

    Hi
    I have seen this on numerous different makes and it usually will remove with some elbow grease and proper stainless cleaner.
    Spillage and stainless grade are possibly a factor.

    Greg

    September 25, 2007 at 8:21 pm in reply to: Bosch WFT2800 dryer not heating up #228337
    gegsy
    Participant

    Re: Bosch WFT2800 dryer not heating up

    If you have checked the other dryer stats then no.
    Without physically being there and diagnosing thats the best I can advise really.
    Your call 😉

    Greg

    September 25, 2007 at 8:12 pm in reply to: Bosch WFT2800 dryer not heating up #228335
    gegsy
    Participant

    Re: Bosch WFT2800 dryer not heating up

    Just making sure, didn’t have time to look. Making the punter do some work 😆 😉 part is available from spares@ukwhitegoods.co.uk 🙂

    Greg

    September 25, 2007 at 8:03 pm in reply to: Bosch WFT2800 dryer not heating up #228333
    gegsy
    Participant

    Re: Bosch WFT2800 dryer not heating up

    It certainly sounds like it from your measurements (ooer)

    Do you have the digits after the GB?? so we can get you a part number for the dryer heater 🙂

    Greg

    September 25, 2007 at 6:41 pm in reply to: NEFF INDUCTION HOB T4243X0 #228560
    gegsy
    Participant

    Re: NEFF INDUCTION HOB T4243X0

    Hi
    Yea white.dna@virgin.net unless you want it to somewhere else 😉

    Greg

    September 25, 2007 at 6:20 pm in reply to: NEFF INDUCTION HOB T4243X0 #228558
    gegsy
    Participant

    Re: NEFF INDUCTION HOB T4243X0

    Hi
    Check your email and erm find your CAPS LOCK BUTTON 😆

    Greg

    September 25, 2007 at 6:16 pm in reply to: BOSCH KSR30420GB/01 NOT COOLING #228623
    gegsy
    Participant

    Re: BOSCH KSR30420GB/01 NOT COOLING

    Hi
    What is the reading of the NTC in relation to temperature?

    Greg

    September 25, 2007 at 5:53 pm in reply to: NEFF INDUCTION HOB T4243X0 #228556
    gegsy
    Participant

    Re: NEFF INDUCTION HOB T4243X0

    What are the numbers after the XO??, so I can send you some stuff 😀

    Greg

    September 24, 2007 at 11:04 pm in reply to: Noisy after changing brushes #228494
    gegsy
    Participant

    Re: Noisy after changing brushes

    As Jim said they should bed in but sometimes if the brushes have worn down to the bone, that the metal connecter to the brush has protruded enough to connect with the commutator, then it either remains noisey or within a short period of spin will abort in the worst case scenario requiring a new motor 😥

    Greg

    September 24, 2007 at 9:46 pm in reply to: bosch not going into full spin #228498
    gegsy
    Participant

    Re: bosch not going into full spin

    Hi
    Have a look here it may help 😉
    http://www.ukwhitegoods.co.uk/modules.p … ge&pid=151

    Greg

  • Author
    Posts
Viewing 15 posts - 1,666 through 1,680 (of 6,724 total)
1 2 3 … 111 112 113 … 447 448 449