gegsy

Forum Replies Created

Viewing 15 posts - 1,771 through 1,785 (of 6,724 total)
  • Author
    Posts
  • in reply to: Finally! #226804
    gegsy
    Participant

    Re: Finally!

    Dear Santa……………… 😀

    Greg

    in reply to: JLWFF 1101 #226725
    gegsy
    Participant

    Re: JLWFF 1101

    I reckon your looking at a Liebherr SBSes7053 beauty there or a hybrid 😉
    If that helps to track fault code down 😀

    Liebherr at the top the John Lewis offering below it

    Greg

    in reply to: Neff S5443 poor water circulation #226717
    gegsy
    Participant

    Re: Neff S5443 poor water circulation

    Most welcome 😉

    Greg

    in reply to: Neff S5443 poor water circulation #226715
    gegsy
    Participant

    Re: Neff S5443 poor water circulation

    …….and also faulty water point unit on heater and/or module. 😀
    You have mail seamy 😉

    Greg

    in reply to: Built-in oven. Any recommendations #226749
    gegsy
    Participant

    Re: Built-in oven. Any recommendations

    Yup agree with you there Helo 😀
    Neff or Bosch have excellent ovens, but don’t expect Diplomat prices 😯
    You get what you pay for, seriously 😉

    Greg

    in reply to: Cannon Oakley 10515g Mk2 Ignition not working #226630
    gegsy
    Participant

    helo_75 wrote:……………….advise you to call someone out

    I would use a Corgi engineer myself 😉
    Try the engineer link below if required 😀

    Greg

    in reply to: aga fridge #226739
    gegsy
    Participant

    Re: aga fridge

    Eh?? thought they only did cooking appliances 😕

    Greg

    in reply to: maytag american f f #226677
    gegsy
    Participant

    Re: maytag american f f

    Have only ever had earth faults on these by the following
    1/ Defrost heater
    2/ Compressor
    3/ Ice maker Unit

    Have sent you circuit diagram by email 😉

    Greg

    PS – Defrost heater was weird, leakage went acceptable when out of circuit but but when I physically meggered it, it read ok 😕 Changed it and hey presto so…………

    in reply to: maytag american f f #226674
    gegsy
    Participant

    Re: maytag american f f

    Was just a thought.
    Have you looked at the dispenser area,esp PCB. Prone to leaks from poorly closing ice flap.
    Solenoid for ice flap goes awol aswell.

    Greg

    in reply to: maytag american f f #226672
    gegsy
    Participant

    Re: maytag american f f

    Wiring loom through hinge chaffing??
    Also need model number, usually starts G……. 😀
    Greg

    in reply to: Bosch d/w SGI43E02GB/08 #226606
    gegsy
    Participant

    Re: Bosch d/w SGI43E02GB/08

    You have mail, section 4.4 😉

    Greg

    in reply to: Bosch d/w SGI43E02GB/08 #226604
    gegsy
    Participant

    Re: Bosch d/w SGI43E02GB/08

    Yup, terrible reliablility.
    What I would say is when you replace the impeller jug, make sure you make a note of the orientation of the old one, its imperative 😉

    Greg

    in reply to: Bosch d/w SGI43E02GB/08 #226601
    gegsy
    Participant

    Re: Bosch d/w SGI43E02GB/08

    Hi senseib
    You must the only person not familiar with THAT hose 😀
    Its situated behind lower front plinth and runs from the metering unit to the sump. It is ‘O’ringed on both ends so will pull off 😯
    Make sure you completely empty sump water before removing the hose (gets a wee wet if ya don’t 😉 )

    Greg

    in reply to: Tradeplace.com #129186
    gegsy
    Participant

    Re: Tradeplace.com

    Tech info for BSH is excellent although Im sure its not what the BSH guys have access to 👿
    Indishit Company portal, agree diagrams and parts and very poor I must say. No tech info (no suprise there :rolls: )cough… nice laptop required 👿

    Greg

    in reply to: bosch touch control hob #226619
    gegsy
    Participant

    Re: bosch touch control hob

    Indicators? do you mean you get numbers indicating power setting?

    Greg

Viewing 15 posts - 1,771 through 1,785 (of 6,724 total)