[gegsy]

Re: bosch classixx dishwasher draining issue

Just a thought, if hubby removes l/h panel, get him to locate polystyrene float.
As you look facing lhs, it will be on the right, with a red plastic stem actuator going down to it.
Mice have a fetish for the polystyrene 😕 and make a mess with poly,causing bits of debris to push actuator bar upwards.

Greg

[gegsy]

Re: bosch classixx dishwasher draining issue

Ok
If he removes lower front panel and removes clear pipe going from sump to anti flood metering unit on the lhs and cleans thoroughly. In extreme cases the metering unit and water matrix on lhs may be gunged up aswel.
This is usually down to lack of rinsing plates before loading, allowing food debris to travel and eventually ferment and grow causing problems.

Greg

[gegsy]

Re: bosch classixx dishwasher draining issue

Hi
When you say under the appliance, did you mean under the stainless steel base where the plastic base is?
You will need the r/h panel off to gain visual access to the base, if there is a leak the water in the base will be apparent. Remove water carefully avoiding unnecessary sloshing around motors etc.
Greg

[gegsy]

Re: bosch classixx dishwasher draining issue

Hi
The model is SRS43C12GB/14.
Let me know when you have located leak 🙂

Greg

[gegsy]

Re: bosch classixx dishwasher drain problem

Hi
Is sounds as if you have a leak into the base below activating the anti flood device.
Please supply full model number. It will be etched on stainless of door at the top as you open it.

If you are to investigate fault, please unplug appliance :plug:

Greg

[gegsy]

Re: BOSCH WFL 2260 NOT DOING ANYTHING!!! HELP!! PUMP BROKEN

Hi
Pump if required is p/no 144484 – £42.50 +Vat and costs.
Available from spares@ukwhitegoods.co.uk

Greg

[gegsy]

Re: snow

N.Wales, sweet FA. Last year it was March before we had anything worth sledging about 😀

Greg

[gegsy]

Re: BOSCH WFL 2260 NOT DOING ANYTHING!!! HELP!! PUMP BROKEN

Not only that Mr P, he will have to look at the make aswell as to if it is a copreci or askoll?

Greg

[gegsy]

Re: Bosch WTE5820gb/04 Condensing TD

Hi
Yea its not bad, take your time no problem.:D

Greg

[gegsy]

Re: Gas Gooker fitter wanted in Winchester

Ok then the only alternative is to find a Corgi engineer here 😉

Greg

[gegsy]

Re: Bosch WTE5820gb/04 Condensing TD

Hi
Best way
1/ Lid off
2/ Undo torx screws that hold r/h panel on behind filter flap/grill at front
3/ Undo torx screws at rear that hold the r/h panel on.
4/ Undo screws on top of r/h side panel IIRC
5/ Once all that is done, the panel should lift up ward and off with a bit of persuasion.
6/ You now have access
7/ Remove small belt and tension jockey arm
8/ You can now gain access to uplift bath assembly, rest is apparent 😀

HTH
Greg

[gegsy]

Re: Bosch SGV 4313 Anti-flood not filling

Hi
Can you supply the full model number, usually etched onto inner door top as you open door.
Greg

[gegsy]

Re: Gas Gooker fitter wanted in Winchester

Hi Mike
Have you tried here 😀 http://www.ukwhitegoods.co.uk/modules.p … whitegoods

Greg

[gegsy]

Re: You are kidding

Go for it :tup:

[gegsy]

Re: You are kidding

Hi Chris :waving:
Great nuts I mean minds eh? 😆
Greg

[Author]

Posts