Forum Replies Created
-
Posts
-
Re: siemans se4200gb/07
stu123 wrote:yes the same as in the post title !! and i was hoping for a actual answer not just a guess at what it may be
stu i think you are quite a rude and martin is a great help so i think you should just appreciate that somebody took the time to read your post and reply to it!!!!
Re: BOSCH wvti2840gb/03 E01 FAULT
went back to the appliance yesterday and found base full of water. The 3 way valve is faulty and dripping water constantly even when not in use. Called bosch as they were cheapest for the part and it is out of stock in this country and needs to come from the mother land (germany). I think there is possibly a big problem with these parts as appliance is only just over 2 years old and seems a bit of a strange fault to me as never seen a valve leak like that.
Re: servis M6006 keeps on filling
£103.50 for me. i called my rep for connect and he didnt seem very keen with the whole discount idea. Just gave some rubbish about having to build a case for me to present to his bosses to see whether i warranted any discount!!!!!
Re: Hotpoint DF53P
if the heater of open circuit it can cause lots of strange faults or if the resetable stat has “popped”. I doubt i timer fault on these dishwashers.
HTH 😕 graham
Re: servis M6006 keeps on filling
hi where do you get a cheap enough module to repair these servis applainces as everytime i come across a module failure the part is £80ish plus vat (from Connect). any advice or help would be greatly appreciated.
ta graham AGM SERVICESRe: BOSCH wvti2840gb/03 E01 FAULT
just had a phone call form the customer saying that she did one wash perfectly then half way through the drying cycle it starting flashing E01 again….aaaaaaaaaahhhhhhhhhhhhhhhhhhhhhh
Any ideas what else could cause this fault???
The pump is activated at the same time and it cycles through the status lights , i.e time remaining, spin etc
Dont really want to part with money i took and would like to help this customer out if possible but dont want to keep ordering spares in the hope one of them fixes the problem.
graham
Re: BOSCH wvti2840gb/03 E01 FAULT
hi, i fitted the Aquasecure and it did the trick…but the old one didnt have red displayed in the little window but was obviously faulty…something to keep an eye out for.
ta for your reply though.
Re: BOSCH wvti2840gb/03 E01 FAULT
hi,thanks for the reply, i didnt notice the red window part on the customers one as first time i had come across this new time of aquastop, but i did see it on the new hose i have ready to fit. So i betg on closer inspection of the custs one that the window has indeed turned red. As i took off the custs hose at supply end i found some yellow putty type stuff on the hoses filter as property is a new build.
Re: Hotpoint TC71 cutting out
reverse timer is 1701133 and timer up top is 1701746. hope this helps.
Re: Hotpoint FZA84
the thermistors on the hotpoint range are non replaceable they rely on the module gathering information from them while they work and if they should fail then the average temp info that the module has gathered keeps it running, But in your case it just sound like a module failure to me. each comes pre programmed (apparantly) with average useage times.
Re: Hotpoint TC71 cutting out
when the tc71 starts to play up like you have described then you would be looking to replace the reverse timer on the right hand side ( as you look at appliance from the front ) at the bottom. take off the right panel and it is at the back on the base. you have replaced the relay which would have been my first bet aswell so i would defo try the rev timer.failing that the main timer is faulty but very unlikely.
Re: Hotpoint WF-340 *Rinse Hold* flashing
yes the chances are a motor tacho fault, i am still in contact with my hotpoint buddies who replace alot of motors and modules on this range.
