Forum Replies Created
-
Posts
-
Re: Zanussi FX1465W – 914792705/00 Washing machine error
Went back out to this machine yesterday with a door lock, but to no avail. I ran the diagnostic but it doesnt do anything when in this position. Everytime you turn the programmer to test a different function it just runs through all its light in the same sequence but doesnt lock the door or do anything.
I looked at the PCB but no obvious sign of damage. No blown tracks etc.Have told the lady i’m pretty sure its the PCB and priced accordingly.
Re: Zanussi FX1465W – 914792705/00 Washing machine error
Thanks for your help Bryan. Just ordered a door lock and will have a go with it tommorrow. It used to happen with the older Zanussi washers, so its got a good chance.
Cheers
Nick
Re: Zanussi Dishasher fault – DE6744 – 91188011/01
I’ll try and get back tommorrow and check out the capacitor. It didnt seem to go open circuit. It seemed to complete the heat cycle perfectly, progress to the emptying stage and then when it should go on to the rinses it just started flashing the error codes.
By the way i wasnt having a go at you for the error codes you gave me, it just wasnt what i wanted to see. Was hoping for a simple fault, especially being my accountants.
Your help is much appreciated Cab.Thanks again
Nick
Re: Zanussi Dishasher fault – DE6744 – 91188011/01
Hells bells, not just a simple, valve faulty or something like that, dam.
I’ve not had the machine to bits yet, but like i say i’ve had it running and it doesnt have anything blocking the motor/pump, dont know what is meant by motor winding interupted but i would assume it was the same as being blocked.
It could i suppose be a loose connection but havent checked yet as for the tachymetric sensor, i havent got a clue what this is or where to even find it.
I was hoping to get this job sorted quickly as its for my accountants and was rather looking forward to getting a bit of my hard earned money back.Kind regards
Nick
Re: HOTPOINT FDW60P error code
Thanks for your help guys. I took the door off yesterday and checked all terminals were connected but couldnt find any problems. Looks like its what i thought it would be the pcb.
Cheers
Nick
Re: Hoover Vision 16 Washer – HV16 31138167 – Plastic button
Cheers for that Dave, without a diagram you just havent got a clue with the titles they give them.
First time i’ve worked on one of these machine. Takes quite a while to get them apart but not that bad to work on once the fronts come off.Thanks again
Nick
Re: Tecnik washer TKL9260 – Belt
Just been on to Bosch and the belt, £6, is out of stock for 10 to 14 days. They can offer an alternative part no 263214 but it will cost £20 plus.
Does anybody know a belt size for this machine?Thanks
Nick
Re: Unbranded dishwasher – BDWFH-1 20001816690
Cheers for that Dave, I’ll order it in the morning.
Thanks
Re: TEKA Dishwasher ADW6 59 FI Fault codes
I could have sworn i heard the solenoid click, when it finished its cold rinse and continued to the heat cycle, but the timing of the fault code sounds about right.
Re: Beko Dishwasher Motor – D2731 FW Stock no: 7875180200
Just been to fit the BEKO d/w motor part number as above and its the wrong one. The motor i need has 3 hoses attached and the one sent is a 2 hose version.
Anybody got any ideas?Thanks
Nick
Re: Creda Cooker 49411
From what i remember it wasnt like the thermostat that youve listed above Dave, i’m sure it had 3/4 contacts. I only had a very quick look at it but it was one that i hadnt seen before. It was only for a rented accomodation so i was in and out like a dose of salts, saying i’d order one from the model number.
Thanks
Nick
