[jonnieboy]

Re: Hotpoint FDW80 tablet stuck in drawer.

there is an adjustment on the top basket just not the typical 2 sets of wheels its the handles at either side of the basket pull them out and up lets the basket lift to a higher position i would guess that some of the customers dinner plates are hitting the top wash arm and preventing it turning during wash cycle the adjustment should solve the problem

[jonnieboy]

Re: Hotpoint AQGMD 149 UK condensor removal?

its the same as the older model widl machines plastic condenser theres a large clamp around the condenser securing it to the tank if you look down the inside of the cabinet you will see it usually its secured with a 7mm bolt not easy to get at but can be done

[jonnieboy]

Re: Hotpoint BWD129 – energising drying solenoid all of the

had the exact problem last week same model and it was the main board think the part no was CO0254298

[jonnieboy]

Re: Indesit DIF04 Dishwasher

if its the main pcb in the base that you changed it needs to be programmed with a smart card and reader

[jonnieboy]

Re: hotpoint wml50

if its the rotary type dispenser there is a modified dispenser out that cures the leak problem part no is
COO281253
fitted loads for nuisance leaks at dispenser and not had a problem well not with leaking from disp lol…. 😀

[jonnieboy]

Re: indesit wixl 143

check the motor brushes sounds like there just about worn out stops the machine working but door stays locked

[jonnieboy]

Re: S’now joke

got a phone call today
when are you doing all the jobs you cancelled

except for the 1 call i managed in that time i cleared my driveway at 8 am got to my 1st [and only] job at 10:20 am which was 6miles from my house got stuck in the customers road until kindly neighbours pushed my van at 11:45 am
with heavy snow falling and cars abondoned everywhere i decided time to head home better to keep myself healthy and my van undented me thinks gets home at 12.50 pm one job complete and completely soaked and exhausted thinking to myself at least i went out and tried
guess who will look out the window next time write the day off and climb back into bed
i was more than willing to do extra jobs etc and make up a half day to be told my 5hours of effort count for nowt !!!!
you gotta laugh when these big companies employ advisers to boost employer/employee relations ❗

[jonnieboy]

Re: Hotpoint WMD960

first check is for worn out motor brushes failing that broken wire at motor plug
hope this helps

[jonnieboy]

Re: hotpoint wmf740

had similar last week it was the motor causing the new door lock to go faulty 🙂

[jonnieboy]

Re: Indesit WIA111 acting wierd

board it is mate remember its a smart card or eeprom job as well

[jonnieboy]

Re: Hotpoint WF860P

defo just plug in and away it goes doesnt need any programming mate 😀

[jonnieboy]

Re: Indesit WIXL123UK/Y Die’s then starts up again

had something similar a while back it was the motor toc going open circuit then reseting machine dies then bursts into life again ❓

[jonnieboy]

Re: hotpoint bwd129 dead

have a good look at the main module a common fault was leaking from the dryer unit onto main board causing weird faults then module burn out

[jonnieboy]

Re: Indesit WE12S Error F28

edit just read post again gotta be f02 motor or f08 heater relay as it blew electrics sounds like f02 motor fault ❗

[jonnieboy]

Re: SCHRIBER APM6855

yep same as rocketman dont believe getting a resistance over the fan motor makes it ok use a magnet on the freezer door so you can visually check fan motor operation
was also told during mfi days by there tech dept if the sensor in the fridge failed its unrepairable as the part is foamed in. ❓

[Author]

Posts