[kneadman]

Re: Daewoo fails to complete wash cycle

Sorry should have said tried with and without a load motor appears to work in both directions and as per programme choice in wash mode or rinse mode works perfectly until countdown jumps from 11 mins back up to 12 until that time has lapsed then stops with error code E8 ….. Suspect Pcb so that was why I was wondering if they can be reset….

[kneadman]

Re: Zanussi zbm878w fan assisted oven not heating up

Thought I would update my results, a second look at the boards showed the large board relays were clicking away when switched on so checked the feed to the small board which gave approx 5 volts…but the relay wasn’t operating..replaced relay still no luck so de-soldiered the transistors and checked…one wasn’t given true reading so replaced it.. all other components checked out everything replaced and now works perfectly…
costs £6, time and patience…
Thanks for your help hope it helps others…

[kneadman]

Re: Zanussi zbm878w fan assisted oven not heating up

Thanks for the reply is there anyway to check the boards I was thinking the larger board which holds the connection for the thermostat most likely controls the neutral for the elements..as the boards appear to cost a fortune don’t want to change one only to find the other is knackered as well….
Thanks for your input….

[kneadman]

Re: Zanussi zbm878w fan assisted oven not heating up

The plate with the pnc no is long gone however here is a photo, the small board has number 372-1361-01b the large one is 372-23-61-10c, hope this helps.

[kneadman]

Re: Hoover Nextra HNWF 3135 will not start

will do have found them via google…thanks for the reply.

[kneadman]

Re: zanussi zwf 12070

cheers will try that first……

[kneadman]

Re: zanussi zwf fails to go to wash cycle.

Hi thanks to all concerned but please close and see next subject zanussi zwf 12070 which has all replies………………

[kneadman]

Re: zanussi zwf 12070

hi to enter machine diagnostics I take it you require an interface n laptop with diagnostic programme….which I don’t have did note a 4 pin connection on the pcb which i examined with large magnification did not see any obvious corrosion or burning tracking ect so if pcb board would need to be a component fault….any easy solution… ❓

[kneadman]

Re: zanussi zwf 12070

Hi would like to thank you for your help and congratulate all concerned in running the site I take it a new board will need to be programmed or will the part work straight from supplier…hoping a complaint direct to zanussi will prove fruitful the machine is only 14 months old….

[kneadman]

Re: zanussi zwf 12070

hi have tried disconnection of hose to pressure switch however still does not fill…I checked the drain hose from the bottom on first day said hose has a plastic ball within through check revealed no blockage within hose or around the ball again this goes all the way up to pressure switch and was clear so with pressure switch isolated machine does not fill so i guess its back to the pcb ?….

[kneadman]

Re: zanussi zwf 12070

Hi have checked the motor.. brushes appear fine good 30mm left on them.. solid no cracks ect.. have checked both solinoids.. main inlet reads 3.62ohms the other 3.68ohms… any suggestions.

[kneadman]

Re: zanussi zwf 12070

thanks for reply the pump is running and the door lock appears to be working as door lock lights up…have checked drain hose for blockages all clear. have checked fill hose which is working. does not operate any programs or will not fill.

[kneadman]

Re: zanussi zwf 12070

washing machine was working fine then next use machine does not fill up does not matter which wash cycle chosen.

[kneadman]

Re: zanussi zwf fails to go to wash cycle.

any input graciously received.

[Author]

Posts