[marley102]

Re: Hotpoint Aquarius door lock problem help

Thanks for the reply iadom, I have opted for a hotpoint engineer as I’m working away and would not like to see the wife meddling in that deep, Accident waiting to happen lol hoping there was a reset or a work around she could have done thanks Nathan

[marley102]

Re: Indesit single oven intermittent fault

Ok thanks for you help bazza500. Will try and get someone to test that for me. Any advice or pitfalls i should watch out for during changing the element, is it a straight forward installation?

[marley102]

Re: Indesit single oven intermittent fault

Hi bazza500, the main rcd on the board trips off when i turn the oven on.

[marley102]

Re: Indesit single oven intermittent fault

Sorry forgot to add that it is on 13a ring main and has been since being installed 4yrs ago. The this ring main is dedicated to the Kitchen only and only has the oven, built-in fridge and freezer on the same ring. thank you in advance for your help.
Nathan

[marley102]

Re: Drain pump help.

Little update. Pulled pump off and stripped(By stripped, i mean unscrewed 3 screws)it down. couldn’t find anything that shouldn’t be there. Put every thing back and seemed to be Good as new, no noise at all. Must have cleared itself. thanks again for info and advice. Great site. 😀

[marley102]

Re: Drain pump help.

I’ll check first, thanks for the info. 🙂

[marley102]

Re: Changing bearing on an Indesit we16uk

Took longer than i imagined, because the inner bearing had collapsed and the race was left on the drum shaft. Managed to get that off, then it was fairly plain sailing.
Thanks again.
This site is an excellent resource. 😀

[marley102]

Re: Changing bearing on an Indesit we16uk

Thanks for the info Phidom.I let you know how it goes.
Thanks again

[marley102]

Re: need help with an indesit we16

thank helo 75 for the reply. I did think this would be the answer. I have just replaced another set of brushes today and also door handle. The question is now whether to purchase another motor in the preparation for the inevitable,or look to purchase a new machine? 😡 Any suggestions on best brands for new machines.

[marley102]

Re: indesit evolution 1600 we16s help

Indeed it was the brushes. On investigation, the brushes were worn away. Received new brushes today and fitted. Machine is now working. Thanks Jim and Hotpnt for your help. I love this site.
Marley102 😀 😀

[marley102]

Re: indesit evolution 1600 we16s help

thanks for pointing me in right direction, I’ll let you know how i get on.
thanks again
marley102

[marley102]

Re: Schreiber Integrated Freezer APP6403

hi paulw97.
no the new board didn’t have a relay on, working fine. glad to here you’ve had success also.this site is brilliant.saved myself a load of cash 😀 .cheers again to all that helped.
marley102

[marley102]

Re: Schreiber Integrated Freezer APP6403

paulw97, i changed the pcb board and the freezer is now working fine,easy job.It seems that a lot of these models have had the same problems.
hope this helps
marley102

[marley102]

Re: Changing a thermostat(app6403)

thanks for all the help I’ve received.My freezer is now working:lol:.The hardest part of that job is pulling the freezer out in the first place.Anyone thinking shall I,Just do it.
thanks again for everyone’s help

Marley102

[marley102]

Re: Changing a thermostat(app6403)

thanks for the reply clive,
at least you know where to start on a dyson.I’ve had a look at the front control panel.obviously doesn’t screw off.does it just pull away from the freezer itself.maybe i should leave it to the experts.trouble is the expert i got couln’t even dignose the problem.
thanks again
marley102

[Author]

Posts