mike100

Forum Replies Created

Viewing 15 posts - 91 through 105 (of 170 total)
1 2 3 … 6 7 8 … 10 11 12
  • Author
    Posts
  • October 31, 2011 at 5:01 pm in reply to: d/w stuck on prog. #361566
    mike100
    Participant

    Re: d/w stuck on prog.

    Ok, resolved this one now.
    It was the long reset as you suggested.
    Thanks for help.
    Mike

    October 31, 2011 at 4:58 pm in reply to: Siemens SE25M575GB/36 d/w keeps stopping #362386
    mike100
    Participant

    Re: Siemens SE25M575GB/36 d/w keeps stopping

    good suggestion, will take a look.
    Thanks, Mike

    October 27, 2011 at 8:12 pm in reply to: d/w stuck on prog. #361565
    mike100
    Participant

    Re: d/w stuck on prog.

    Thanks for that.

    Do you happen to have the part no for the user board as I think it may well be that.
    Mike

    October 18, 2011 at 10:00 pm in reply to: Miele dishwasher G977 Plus inlet/drain flashing #361640
    mike100
    Participant

    Re: Miele dishwasher G977 Plus inlet/drain flashing

    paper or muck sometimes gets stuck in the circ. pump impeller.

    Lay machine on side , take off base plate and take out circ. pump. Not difficult job.
    Mike

    October 6, 2011 at 5:55 pm in reply to: Freezer keeps on running EU2246c #360720
    mike100
    Participant

    Re: Freezer keeps on running EU2246c

    Probably 10 plus years. It seems to be freezing fine. Its just that the motor runs for longer than it used to says customer
    Mike

    October 5, 2011 at 6:01 pm in reply to: miele g646sc D/W inlet/outlet light flashing #360619
    mike100
    Participant

    Re: miele g646sc D/W inlet/outlet light flashing

    could be paper or stuff in circ. pump impeller. You will need to take out motor. Not too bad lying on its side.
    Mike

    October 3, 2011 at 3:45 pm in reply to: neff oven burn marks on fridge next to it hbn9123gb/02 #360263
    mike100
    Participant

    Re: neff oven burn marks on fridge next to it hbn9123g

    Thanks guys. Getting some receivers then trying leak test via martin.
    Mike

    October 3, 2011 at 3:42 pm in reply to: bosch washer stuck on prog #360265
    mike100
    Participant

    Re: bosch washer stuck on prog

    Thanks Paul, thats what it was.
    Mike

    September 29, 2011 at 4:04 pm in reply to: Hotpoint Door not opening #360127
    mike100
    Participant

    Re: Hotpoint Door not opening

    Thanks Dave for that.
    Is it possible to solder on new part or do I have to get another board.
    Mike

    September 29, 2011 at 4:02 pm in reply to: Where is the fuse #360087
    mike100
    Participant

    Re: Where is the fuse

    Thanks Spanner, found it in loom as you pointed out from picture. Fuse is ok. Looks like it is the lid switch that has fallen apart.
    How do you get the lid off to get at it. Also is the part no. 481903950298.
    Thanks
    Mike

    August 23, 2011 at 7:06 pm in reply to: cda ci 950 belt #357305
    mike100
    Participant

    Re: cda ci 950 belt

    Thanks for that, great help.

    Mike

    May 5, 2011 at 5:50 pm in reply to: WhirlpoolTop Loader Pump sleeve #350601
    mike100
    Participant

    Re: WhirlpoolTop Loader Pump sleeve

    ok ta, will give them a call.
    Mike

    April 25, 2011 at 5:35 pm in reply to: Admiral Top Loader #349937
    mike100
    Participant

    Re: Admiral Top Loader

    Many thanks for your help John.

    Mike

    April 24, 2011 at 6:34 pm in reply to: Admiral Top Loader #349935
    mike100
    Participant

    Re: Admiral Top Loader

    Thanks John for that. Yes the adaptor/sleeve was stuck in the old pump but it was jammed in and bust when I tried to get it out.

    Do you know where I could get this part. The Admiral spares company didnt recognise the model no.

    Maybe I should go the Trade spares forum.

    The model no is:

    3RATW3005TQO

    MIke

    April 2, 2011 at 6:41 pm in reply to: Bosch Maxx 6 WAE 24190NL/03 #348408
    mike100
    Participant

    Re: Bosch Maxx 6 WAE 24190NL/03

    Tried another Aquastop hose, still the same.

    Fitted ordinary inlet hose now works fine.

    When I tested there was no power to Aquastop plug so maybe there is a fault coming out of the board.

    Anyway thanks for your answers.

    Mike

  • Author
    Posts
Viewing 15 posts - 91 through 105 (of 170 total)
1 2 3 … 6 7 8 … 10 11 12