monkey

Forum Replies Created

Viewing 15 posts - 61 through 75 (of 80 total)
1 2 3 4 5 6
  • Author
    Posts
  • September 16, 2007 at 5:29 pm in reply to: Hotpoint D41uk no pump #227705
    monkey
    Participant

    Re: Hotpoint D41uk no pump

    one nuetral and no feed from pcb

    September 16, 2007 at 12:58 pm in reply to: Hotpoint D41uk no pump #227703
    monkey
    Participant

    Re: Hotpoint D41uk no pump

    I have checked with the meter. no power

    August 26, 2007 at 5:32 pm in reply to: Indesit D61UK pcb #225356
    monkey
    Participant

    Re: Indesit D61UK pcb

    Sorry Guys
    It was D41UK when I rechecked the model number but I did have the correct serial number.

    August 25, 2007 at 6:11 am in reply to: Indesit D61UK pcb #225354
    monkey
    Participant

    Re: Indesit D61UK pcb

    Hi Guys
    yes I have been out to this dishwasher.When I put the model no. into masterparts search it came up with the same part no. But it has pcb and not a timer that is why I gave you the serial no.

    August 17, 2007 at 6:45 am in reply to: Hotpoint FDW80P No Power #224794
    monkey
    Participant

    Re: Hotpoint FDW80P No Power

    Hi
    It is later one with the LCD display. This is a real puzzler I could do with somehelp

    July 31, 2007 at 7:06 am in reply to: Hotpoint FDW80P NTC #222947
    monkey
    Participant

    Re: Hotpoint FDW80P NTC

    Hi Guys
    The serial number is 37331870900/603311105
    I hope this helps
    monkey

    May 31, 2007 at 9:02 pm in reply to: Miele G560W Leaking #215422
    monkey
    Participant

    the front and back and side panels are all joined together.I dont suppose you have a service manual

    May 31, 2007 at 9:00 pm in reply to: Hotpoint VTD00P #215427
    monkey
    Participant

    customer as had a go at changing belt and disconnected wires everywhere

    May 24, 2007 at 7:08 am in reply to: Zanussi ZFK62/23 prod no 925751613 #214625
    monkey
    Participant

    This model does not have any ducts in it.I think it may have a valve somewhere

    April 14, 2007 at 8:10 pm in reply to: Miele w853 Rinse hold light flashing #210704
    monkey
    Participant

    Re: Miele w853 Rinse hold light flashing

    Thanks how do I repair it.

    March 27, 2007 at 6:04 pm in reply to: Dyson dc07 animal wont pick up #208980
    monkey
    Participant

    Hose is not split there is plenty of suction

    February 27, 2007 at 7:28 pm in reply to: Bosch SGS45EO8GB/45 program #205580
    monkey
    Participant

    do you have a wiring diagram for this model

    February 25, 2007 at 4:33 pm in reply to: Bosch SGS45EO8GB/45 program #205578
    monkey
    Participant

    I have tried that but you only have 2 wires going to the door switch and the machine would work in reverse which it does not.

    November 19, 2006 at 7:05 pm in reply to: aeg72620w Bearings #195878
    monkey
    Participant

    thanks for that part no. but this is the shaft
    assy. and I only need the collar for the seal to
    run on. I was thinking do you have to heat the collar up to fit over the shaft ?

    November 9, 2006 at 9:28 pm in reply to: servis M4306 No Heat #194758
    monkey
    Participant

    Re: servis M4306 No Heat

    I have checked the thermostats there is two on the heater box, the one on the end of the heater is open circuit, but I dont know if this is normally open.The one on the top of the heater box is a safety stat this has not tripped out. any information would help, especially a wiring diagram.

  • Author
    Posts
Viewing 15 posts - 61 through 75 (of 80 total)
1 2 3 4 5 6