Forum Replies Created
-
Posts
-
Re: Zanussi ZWF16070W Lights and nothing except door interlo
try replacing the interlock failing that it could be the PCB
Re: Zanussi ZWF12070W1 Door Will Not Open at End of Cycle
possibly a blockage in the or near the pump , try clearing the pump and attached hoses, may help .
Re: Indesit WIA121 machine has power but nothing happens
Thanks iadom
I will give that a go, but I would have thought it would have still filled with water ? as I said I do as normal set it to whatever program I want usually 4 or 5 or spin only, everything seems to ba as normal lights go thru the sequence then it should starts to fill up with water but nothing.
all that happens is after the sequence of lights any one of the 3 lights at the side of the dial will stay lit ? u then hear the door interlock click and nothing happens ???????? but as u say i’ll try the brushes, I will do this tomorrow and report back, if this does the trick great , thanks again
sorry iadom the reason I change machines is I enjoy doing DIY and as I dont earn alot of money in the job I have, I try to do as best I can with 2nd hand machines I work for the cleansing dept with our local council & I look out for wash,dryer machines that I think are better than the one I already have . I only just got this machine it was thrown out but looked brand new so I took it home hoping that there would not be much wrong with it , which I was hoping I could repair myself saving me money, I hope this answers your question , and would appreciate if you would remove your post as you are trying to insinuate that I work in the trade .
thanksHOTPOINT WF325 how do I gain access to replace the element
I just discovered the element on this machine is at the rear of the drum can anyone help how I go about getting access to the element as there doesnt seem to be a back panel looks like a sealed back panel ???, is this a complete drum removal thru the top of the machine to gain access to the element ????
any help much appreciated
ThanksRe: HOTPOINT WF325 STUCK IN WASH CYCLE, DOES NOT ADVANCE
THANKS Penguin45
I WILL CHECK THE HEATER ELEMENT FOR CONTINUITY, IF THIS IS THE FAULT ARE THEY EASY TO FIT ?
THANKS AGAINRe: Hotpoint WD440 / NO WATER GOING INTO MACHINE & goes
Thanks for the reply , I think all the lights flash on and off then the 1st 2 lights stay on while lights 3 ,4 & 5 go off , hope this helps.
look forward 2to your reply
tHANKSRe: ZANUSSI FL881 WASHING MACH WONT STOP FILLING,PLEASE HELP
Hi
checked and blown thru the 2 black tubes which seem clear no holes etc, checked both pressure switches large cream coloured switch when blown into clicks twice , the smaller one of the 2 when blown into clicks once, I guess these are ok, the only thing I am unsure of is the module? can you explain abit more with regards to module ???where its located ? its purpose etc ??any more help or info much appreciated, as still not rectified the problem.
ThanksRe: ZANUSSI FL881 WASHING MACH WONT STOP FILLING,PLEASE HELP
Hi bryan
When the machine is off no water fill, but whenever I set it to any of the programs, pull the dial out to (on) the machine starts to fill but doesnt stop filling ? but will stop filling if I push the on /off dial in to stop program.
hope this helps.
ThanksRe: Hoover WDM 120 Motor / Armiture struggles to turn ????
I had another look at the machine the program in use at the time was a woolens wash , I changed the program to spin cycle and the same happened BUT this time I helped the big wheel at the back of the machine by turning it while the motor was trying to go into a spin & it worked but was a bit sluggish at times although once it gained speed it worked fine spun the clothes, the reason I have added to the reply is if the armiture or the motor is at fault then WHY ? did it spin all be it with a little help from myself ? I dont doubt you guys but before I purchase a motor I want to be sure . can anyone shed abit more light on the subject ?
Thanks for the replies
