Forum Replies Created
-
Posts
-
Re: Electrolux EWX14540W ERROR CODE ed4
ok Martin…thank you…i’ll try a new element although i do wonder how a faulty element can affect it if it’s disconnected…i am a doubting Thomas…haha….i’ll let you know….thank you….john
Re: Electrolux EWX14540W ERROR CODE ed4
hi Martin….thanks…..i have noticed a couple of other things that aren’t right…..if i set the dryer setting the time goes to 12 mins automatically!…..if i disconnect the dryer element and run it through a wash cycle , at the end of the cycle the dryer starts up and there is still water left in the drum…are these things also connected with the dryer element?,,.thank you…john
Re: AEG Oko-Lavamat 1271 VI Turbo – not completing cycle
hi…thanks for your reply…mine seems to be working ok now..washer and dryer..i think resetting between cycles has a lot to do with it…thank you
Re: AEG Oko-Lavamat 1271 VI Turbo – not completing cycle
hi….i am having the exact same problem with my aeg 1271 machine…did you ever find the problem?…thanks…john
Re: miele dishwasher g638plus flooding
hi Seamy. thank you for your reply.what i have done is replace the salts container with the solenoid valve and the little chip on the front..this has cured the problem..therefore i assume the water matrix,including the flow meter and solenoid valve are all ok..the waterproof inlet hose is indeed on the outside – it is the rubber hose next to it that is forced off – goes from matrix to bottom of salts container ..i will double check the softener exit hose is not blocked…could it be the solenoid valve on the side of the salts container that is faulty? The water matrix does not fill-it is as if water is entering the matrix, going straight into the bottom of the salts container and pretty quickly blowing the tube off because the water has nowhere else to go…thank you very much for your help..john
Re: miele dishwasher g638plus flooding
hi….just to clarify…it’s as if the water cannot flow from the water matrix through the water softener part of the plastic salts container into the tub! the softener plastic bulges under the pressure until the rubber pipe comes off the bottom…. hope this is clearer and somebody can help me…thanks….john
Re: aeg L16830 washer/dryer door interlock problem
ok Andy……I’ll try a replacement and let you know the result in a few days….many thanks for your help….john
Re: aeg L16830 washer/dryer door interlock problem
ok..thanks….it’s not the pause button…..the machine otherwise functions perfectly…..i started a wash 15mins ago and the door light remained green….looked just now and it is red! at the end of a cycle there is no or little delay before i can open the door ….sometimes the lock can click a few times like it’s trying to lock….is there a way i can test the lock if i remove it? thanks…john
Re: bosch wfl245s program problem
hi martin..AAA+++..yes….you’re a genius……i fitted a used cable harness today…haven’t plumbed it in properly yet but the spin cycle works perfect…..i would never have worked out the problem without your help….thank you very much….john…
Re: bosch wfl245s program problem
ok martin….one of the wires did pull out fairly easily from the motor connection block!..although not really loose(an end one-bottom)…i need a new wiring loom now anyway…doesn’t seem to be on spares list so i’ll make a spares inquiry in the morning…..i’ll be impressed if you’re right…..i’ll let you know….thank you very much….john
Re: bosch wfl245s program problem
hi martin…..no broken wires…i was thinking that as the machine started the cycle and then behaved normally for at lease 20mins.when it then suddenly went into a fast spin for a few secs – at first i thought it was the belt coming off again…maybe it’s just coincidence that it’s gone wrong just after changing the bearings….i’m thinking i should try a different motor…what do you think?….thanks…john
Re: bosch wfl245s program problem
ok martin……i’ll have a good look and let you know how i get on….thank you….john
Re: bosch wfl245s program problem
thanks martin…..i’ve just looked inside the motor..nothing visibly broken….which part is the tacho generator? i’m assuming i can take the motor somewhere and get it tested properly? thanks for your help…john
