Forum Replies Created
-
Posts
-
alexa wrote:PaulG
And you had a bad back!
And the mind is working overtime as to the massage method
😀 I think she said Swedish 😉
Re: Bra wires
Any chance this can get moved to the general forum, not just for the charity thing, but because I asked a genuine question on the biggest wire you engineers have pulled out of a washer?
Re: Bra wires
SHe is a massue for a living, with me having a bad back, she offered to give me a massage 😯 Sadly, I’m no longer doing her area.
P.S she is a proper one, not one of those dodgy ones that offer extras. 😆
Re: Vaccuum cleaners
Sadly I don’t have an account with them, but would be prepaired to have one, if they allow sole traders. DO you have a contact number atall?
Re: BOSCH MAXX IT on meltdown, can someone help please
Small world aint it, I was at Benson’s house to look at his dishwasher.
Re: After 6pm calls
Toni wrote:As a one man band in my area, I dont get much choice. If I dont do them someone else will. I find that the customers who want an after 6 appointment are usually proffesional people who can’t or wont take the time off work, but if they want anything after 5pm from me it does cost them an extra £25.00. most are ok with this. I tend to book late appointments only on Tuesdays and Thursdays and I find most customers will wait if they have to for the late appointment.
Toni
Thanks, that’s similar to what I had in mind, once i’m without contract.
Re: After 6pm calls
Kwatt, in your opinion, would it be fair, to increase the labour charge, for such an appointment?
Re: Whirlpool dishwasher DWF416
Don’t know about the dispenser coil, but I know the ones with ascol wash motors have been stuttering, like how you described.
Re: F4 on adp5966 whirlpool dishwasher
rino345 wrote:My dishwasher is also having the same problem (F4), seems like it might be the pump, I can hear the motor come on but no water are being pumped. Postcode is SP10, can someone give me an idea what repairs would cost. Engineer + new parts.
Thinking of buying a new dishwasher, Hoover, hopefully more reliable then this piece of …………; Hoover is about £250.
🙁 🙁 🙁 🙁
Try Service87 in Alton Hants. Sorry, I don’t have tel no handy.Re: Hoover Performa 1300 – Unable to drain
Anonymous wrote:the impellor was obstructed by a wire, works now, thanks for your help!!
cheers
I’ll pm you where to send the cheque to 😉
Re: Ford Connect Premature Tyre Wear
Alex wrote:We have a few of these vans, bought new in the summer. We have found the tyres have worn excessively on the front wheels, inner edge. In fact 1 van was illegal at 8,000 miles. The wear is only visible if you turn to full lock, then you will see the wires are prodruding.
.
😆 😆 The van is doing fine BTW.Re: Hoover Performa 1300 – Unable to drain
Hi Guest, firstly, to check for blockages, lower the waste pipe into a bowl, if the water runs out freely, then you can assume you do not have a blockage. This really only leaves ‘a pump problem’, going by what you have already wrote, I gather that you are capable of removing the pump. Check that the impellor isn’t obstructed, if it is free of obstructions, you can assume it is goosed, go out to a spares shop, buy a new one and fit it.
Re: Recons
kwatt wrote:Given that, what’s the point of recons if you can’t get a decent supply of quality appliances to recon?
Hi Kwatt, thats the point I was trying to make on the Remploy thread, they have taken away MY only source of ‘scrapped’ appliances by somehow getting the big scrap contracts. At a guess, I’d say Remploy are riding on a wave of political correctness, with a ‘recycle, employ disabled’ policy. I’d be interested to know how many small businesses have lost their main source of income, due to the Remploy take over?
You see, it wasn’t just about reconing, these appliance graveyards were good for otherwise expensive parts. It was a gamble to buy a machine, hoping the module/timer/motor worked, but I can honestly say, I have never lost the gamble when buying a scrapper for a certain part.
Anyways, the way to go is new and manu warranty from now on.
