Penguin45

Forum Replies Created

Viewing 15 posts - 15,766 through 15,780 (of 19,678 total)
1 2 3 … 1,051 1,052 1,053 … 1,310 1,311 1,312
  • Author
    Posts
  • February 26, 2006 at 2:35 pm in reply to: candy cr162k #166726
    Penguin45
    Participant

    Re: candy cr162k

    91941516, about £11, special order from Masterpart.

    Chris.

    February 26, 2006 at 11:58 am in reply to: Error code help #166550
    Penguin45
    Participant

    Re: Error code help

    Yup, it should fit. They have used a couple of different manufacturers for the pumps over the years, but they do interchange.

    Regards,
    Penguin45.

    February 26, 2006 at 12:28 am in reply to: Ariston ASD 70C Dryer – Error code F11 #166714
    Penguin45
    Participant

    Re: Ariston ASD 70C Dryer – Error code F11

    This appears to be a European specification model – I can find no information immediately.

    For other UK readers, this seems to be a Hotpoint/Creda machine with digital control, badged as an Ariston.

    Based on our extensive experience of these appliances in the UK, I’d take a guess at no heat, but it’s no more than that.

    Regards,
    Penguin45.

    February 25, 2006 at 8:53 pm in reply to: Ariston AFA350 X or LS 12 – BIT100 #166703
    Penguin45
    Participant

    Re: Ariston AFA350 X or LS 12 – BIT100

    the_max_sti wrote:Is this a case of get a new main board for it and hope..

    Stop. That’s how expensive mistakes are made…….. We can’t tell you blow by blow how to repair your appliance for variety of reasons, but here are a couple of pointers.

    The single most common failure on these appliances is the heater – it should have a reading of 25-50 ohms. There is no flow meter fitted – the water level is controlled by the displacement of air into a pressure operated switch. It will be attached to a skinny hose.

    Power off, of course.

    Regards,
    Penguin45.

    February 25, 2006 at 8:36 pm in reply to: Hotpoint aquarius dwf50p manual #166705
    Penguin45
    Participant

    Re: Hotpoint aquarius dwf50p manual

    Looks like you’ll have to give them a ring on Monday and pay them a couple of quid. Tel. 08709 077077.

    Regards,
    Penguin45.

    February 25, 2006 at 8:26 pm in reply to: Stock Available #166223
    Penguin45
    Participant

    Re: Stock Available

    Thanks for the offer Kevin, but there’s no panic.
    Enjoy a Sunday off?

    Chris.

    February 25, 2006 at 4:51 pm in reply to: AEG Competence B8340-1 fault ‘F7’ #166157
    Penguin45
    Participant

    Re: AEG Competence B8340-1 fault ‘F7’

    Thanks for the update.

    Spares pricing is an ongoing contentious issue in this industry and is among the reasons that this site exists.

    Regards,
    Penguin45.

    February 25, 2006 at 4:39 pm in reply to: AEG Lavamat 6955 F8 Error code not clearing #166680
    Penguin45
    Participant

    Re: AEG Lavamat 6955 F8 Error code not clearing

    Try holding down the start button, then switching on. May clear it.

    Regards,
    Penguin45.

    February 25, 2006 at 4:28 pm in reply to: Zanussie DE 6854 Not Heating #166699
    Penguin45
    Participant

    Re: Zanussie DE 6854 Not Heating

    Heater or contol board likely candidates. There are 8 (!) versions of this machine, so pnc number would help for further info.

    Power off if investigating or click the link below for help.

    Regards,
    Penguin45.

    February 25, 2006 at 4:23 pm in reply to: Caple DI414 Dish-no-washer! #166619
    Penguin45
    Participant

    Re: Caple DI414 Dish-no-washer!

    Sounds like it’s underfilling – the water should fully cover the central recess of the cavity. Usually a bit of a demolition job to resolve as various hoses and air chambers need to be removed and cleaned.

    Click the link below for pro help if you’re not confident with this, power off if you’re going to investigate further.

    Regards,
    Penguin45.

    February 25, 2006 at 4:19 pm in reply to: Ariston AFA350 X or LS 12 – BIT100 #166700
    Penguin45
    Participant

    Re: Ariston AFA350 X or LS 12 – BIT100

    If you go with the codes, strictly speaking it means that the inlet valve isn’t working! However, the codes are notoriously unreliable, as are the elctronics themselves, so unless you know how to use a mulimeter correctly and safely, you may well be on a hiding to nothing with this one.

    Pro help may well be your best option – click the link below.

    Power off if you are going to investigate further.

    Regards,
    Penguin45.

    February 25, 2006 at 4:03 pm in reply to: Door bottle rack for neff built in fridge type KA4313XOGB #166679
    Penguin45
    Participant

    Re: Door bottle rack for neff built in fridge type KA4313XOG

    http://www.bshappliancecare.com is the spares site. Check your model number as I can find no reference to it.

    Regards,
    Penguin45.

    February 25, 2006 at 3:56 pm in reply to: Stock Available #166220
    Penguin45
    Participant

    Re: Stock Available

    Guess what they tried to deliver on Friday whilst I was at the meeting? 👿

    Chris.

    February 23, 2006 at 1:48 am in reply to: Error code help #166546
    Penguin45
    Participant

    Re: Error code help

    It ain’t pumping out fast enough……. Check for blockages, kinked/crushed drain hose. Remember that the pump is live as long as the machine is plugged in.

    Regards,
    Penguin45.

    February 23, 2006 at 12:49 am in reply to: I can hear an echo? #166483
    Penguin45
    Participant

    Re: I can hear an echo?

    There seems to be a tradition that when all else fails we take a pop at the rotating puddle…..

    Or are we being all corporate these days?

    Chris.

  • Author
    Posts
Viewing 15 posts - 15,766 through 15,780 (of 19,678 total)
1 2 3 … 1,051 1,052 1,053 … 1,310 1,311 1,312