Forum Replies Created
-
Posts
-
Re: Indesit WIL103 Door Seal replacement
Band with screw goes into groove around door seal at the tub end – do this first – completely impossible with front of seal fitted. Then pull the seal over the lip at the door end, fit skinny band with spring into groove.
As you must remove the lid for access ensure that power is off :plug: .
Good luck,
Penguin45.Re: zanussi front panels
If you are lucky, the switch will have slipped out of the clips and can be snapped back into place. If you are unlucky the lugs will have broken and the console panel will need replacing.
P/no is 1525744-81/7 – £55.88 😯 – plus VAT etc.
Power off before further investigations.
Regards,
Penguin45.Re: Bosch SMS 903 Dishwasher not using salt
Regret SMS903 is not a valid model number – please recheck.
Initial thought would be some sort of solenoid failure on the fill matrix.Regards,
Penguin45.Re: Neff: water left at end of cycle / lights gone out / dry
It sounds like the power supply on the computer board is on its way out. Due to the expense of the component, I would definitely get this checked by an engineer.
Regards,
Penguin45.Re: Penguin45 – Conspiracy Theory – I Confess
Further to our plan to take over the world, I can offer you the first glimpse of our latest secret weapon – The V1 Penguin.
http://www.nationalgeographic.com/critt … stcard.jpg
Chris.
Re: Help! Hotpoint WD41 Washer/Dryer instantly tripping RCD.
8 is correct – it was late and I was tired……
Good luck,
Penguin45.Re: Zanussi ZK56
Lots of different versions of this one – pnc number will be required. Have a look round the crisper bin for the rating label.
The good news appears to be that the seals are available separately, so spares@ukwhitegoods.com will be able to source it for you.
Regards,
Penguin45.Re: Indesit W93
Module is part number C00080981. Typically, being Sunday I can’t find a price for it 🙄 . Dave Conway will be able to advise you later no doubt.
The module is supplied without the eeprom (small processor), so you have to transfer that across.
Bear in mind that no spares supplier will ever take back an electronic board under any circumstance, so be absolutely certain of your diagnosis……..
Regards,
Penguin45.Re: 4 u Penguin
Julia is busy shooting Penguins even as I type….. I quote –
“It’s the big one you’ve got to watch”.Been saying that for years to no effect……….
Chris
Re: Now I Know…
Nah, they don’t have horses left over there – still lots of sheep though………
Anyway Alexa, you’re out numbered by the little white fluffy blighters by a bout 3 to 1 IIRC, so you’re in no position to talk. 😆
Chris.
Re: Help! Hotpoint WD41 Washer/Dryer instantly tripping RCD.
Mains filter is p/no 1602467 – eMail to spares@ukwhitegoods.com will get things moving for you.
Any reading to earth of 2Meg or less should trip the RCD, so allowing for Ray’s comments you are on the right track.
Regards,
Penguin45.Re: White Knight CL447 dryer Push start!
Diagnosis is correct, you want one of these:
http://www.ukwhitegoods.co.uk/modules.p … ucts_id=94
All readers be advised that push starting the motor isnot a safe procedure – fingers have been lost over the years.
Regards,
Penguin45.Re: AEG L16810 Not drying
Basic problem is that this is a Zanussi washer dryer in a posh skirt……
Your problem will almost certainly be the condenser housing in the rear right corner of the machine as you look at it. It fills with fluff to such a degree that it restricts the air flow around the machine. Accessing it involves splitting the rear casing from the machine and thoroughly cleaning out.
Power off please………
Regards,
Penguin45.
