Ray9500

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 72 total)
1 2 3 4 5
  • Author
    Posts
  • September 26, 2017 at 1:06 pm in reply to: Miele H4641 #450669
    Ray9500
    Participant

    Re: Miele H4641

    Thanks Dave,

    I didn’t think they would be helpful without the service number?
    I’ll give it a go though 😀

    November 6, 2016 at 9:07 pm in reply to: Bosch WVD24460GB/05 Washer dryer #441959
    Ray9500
    Participant

    Re: Bosch WVD24460GB/05 Washer dryer

    For the sake of anyone searching, the fault on both of these was a sock caught on the heating element in the same spot on both machines! I’m assuming this was upsetting the pressure switch as the air chamber comes off the sump hose 😉

    October 28, 2016 at 7:13 am in reply to: Britannia SI-10T6-i-s #442072
    Ray9500
    Participant

    Re: Britannia SI-10T6-i-s

    Supplied by the nice people at Britannia 😀

    October 19, 2016 at 7:33 pm in reply to: Indesit DIF04B1UK fault #441927
    Ray9500
    Participant

    Re: Indesit DIF04B1UK fault

    Hi Simon,
    Have you had a look at the main pcb, maybe some damage there?
    I’ve not had this fault before, do the lights flashing correspond to any fault codes?


    Regards
    Ray

    October 7, 2016 at 8:19 am in reply to: Miele G1022SC #441551
    Ray9500
    Participant

    Re: Miele G1022SC

    Morning Steve,
    Might be worth checking the wash motor impeller for blockages, that stops a pressure switch being activated and starts the lights flashing.
    Had the same symptoms a while back and was kindly helped on here 😀
    Regards, Ray

    June 3, 2016 at 7:20 am in reply to: Miele G4100 57/100799235 Dishwasher #437996
    Ray9500
    Participant

    Re: Miele G4100 57/100799235 Dishwasher

    You were all absolutely right, it was quite a few wrappers etc buried in the impellor.
    All done and dusted, Many thanks! 😀

    June 1, 2016 at 7:04 am in reply to: Whirlpool wwdc6400/1 #437849
    Ray9500
    Participant

    Re: Whirlpool wwdc6400/1

    Sorry, forgot to say I’ve sent you a pm! :tup:

    May 24, 2016 at 7:00 am in reply to: Howdens Hja8701 Washer dryer #437819
    Ray9500
    Participant

    Re: Howdens Hja8701 Washer dryer

    Thanks for the replies 🙂
    I’ve checked the condenser but not the fan blades, will check and report!

    June 24, 2015 at 6:44 pm in reply to: Admiral GC2027HNKBS front panel #427875
    Ray9500
    Participant

    Re: Admiral GC2027HNKBS front panel

    Quick update, spot on Steve!
    Removed the freezer door handle, took off door hinge undone two screws under the handle and lifted off door skin to access display module. Took around 30 minutes and the new module cured the problem 😀
    Thanks again!

    June 4, 2015 at 12:22 pm in reply to: Admiral GC2027HNKBS front panel #427874
    Ray9500
    Participant

    Re: Admiral GC2027HNKBS front panel

    Many thanks Steve, wasn’t sure whether to attempt that but will now 😀

    Ray

    May 21, 2015 at 8:06 am in reply to: AEG dishwasher module setup? #427073
    Ray9500
    Participant

    Re: AEG dishwasher module setup?

    Quick update, nothing in the manual regarding any setup procedure on a configured module.
    I fitted an older module and it all worked fine, on contacting Electrolux customer service and explaining the modules they were sending me are unconfigured i got this: ‘The parts we have sold to you are in perfect working order and have been
    tested in Europe and we do not have any problem with our stock’
    Very helpful!
    Anyhoo, thanks for your help Dave 🙂

    Ray

    May 7, 2015 at 10:09 am in reply to: AEG dishwasher module setup? #427072
    Ray9500
    Participant

    Re: AEG dishwasher module setup?

    Many thanks Dave, much appreciated.
    I’ll update results as soon as I get to grips with it again 🙂

    July 2, 2013 at 4:01 pm in reply to: Whirlpool ADP7955 Touch diagnostics #397005
    Ray9500
    Participant

    Re: Whirlpool ADP7955 Touch diagnostics

    Help! Not a lot of info on these it seems 🙁
    Any pointers at all would be appreciated 🙂
    Thanks in advance
    Ray

    December 20, 2012 at 9:15 am in reply to: Hotpoint BCI450 fault codes? #386567
    Ray9500
    Participant

    Re: Hotpoint BCI450 fault codes?

    Many thanks Geoff, looks like the module as it heats up fine.

    Ray

    September 21, 2011 at 4:18 pm in reply to: WAE24364gb/11 #359503
    Ray9500
    Participant

    Re: WAE24364gb/11

    Thanks Martin, i am reluctant to change the module in case some thing happens to it afterwards! This machine seems possessed!
    Ray

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 72 total)
1 2 3 4 5