RHrepairs

Forum Replies Created

Viewing 13 posts - 61 through 73 (of 73 total)
1 2 3 4 5
  • Author
    Posts
  • January 15, 2014 at 1:30 pm in reply to: whirlpool dishwasher adg7440 11flashes #407640
    RHrepairs
    Participant

    Re: whirlpool dishwasher adg7440 11flashes

    Found broken wires down by the door, fixed and now has rectified the problem

    November 6, 2013 at 12:43 pm in reply to: hotpoint bwd129 quick wash light flashing #404053
    RHrepairs
    Participant

    Re: hotpoint bwd129 quick wash light flashing

    thanking you

    November 6, 2013 at 10:38 am in reply to: Hoover washer dryer HWD 130-80 door light flashing #403250
    RHrepairs
    Participant

    Re: Hoover washer dryer HWD 130-80 door light flashing

    got the pcb back from a local person who repairs pcb, the was two loose connection on it, problem solved

    October 23, 2013 at 1:25 pm in reply to: Hoover washer dryer HWD 130-80 door light flashing #403248
    RHrepairs
    Participant

    Re: Hoover washer dryer HWD 130-80 door light flashing

    All the TOCs are closed circuit…its just strange that just the protective casing is melted an no other part of the machine is. E.g. facia panel etc

    July 11, 2013 at 7:52 am in reply to: Hotpoint washing machine HVL241 filling abnormally #397409
    RHrepairs
    Participant

    Re: Hotpoint washing machine HVL241 filling abnormally

    Can you replace those traics individually?

    May 10, 2013 at 7:04 pm in reply to: indesit idf125 not heating/ not washing properly #394691
    RHrepairs
    Participant

    Re: indesit idf125 not heating/ not washing properly

    Would a break in the wiring happen often in this model? I did a test programme and it did it ok without any faults showing

    March 26, 2013 at 3:13 pm in reply to: Zanussi ZSF6161 flood reset #277393
    RHrepairs
    Participant

    Re: Zanussi ZSF6161 flood reset

    i have the same problem…..i30, no leakage, the antiflood device works perfect, took off fill matrix and cleaned it out. Check pressure switches for blockages and nothing so could it be the board?

    March 18, 2013 at 9:47 pm in reply to: hotpoint wf340 door lock but no door light. #392136
    RHrepairs
    Participant

    Re: hotpoint wf340 door lock but no door light.

    Ya turns out it was the brushes.

    March 13, 2013 at 10:15 pm in reply to: whirlpool washerdryer awz410 constantly filling #391966
    RHrepairs
    Participant

    Re: whirlpool washerdryer awz410 constantly filling

    Replaced the valves and pressure switch and still the same outcome. Going to try the module in the morning.

    November 28, 2012 at 1:43 pm in reply to: siemens dishwasher #385476
    RHrepairs
    Participant

    Re: siemens dishwasher

    Thanks, got it sorted…..the board blew so im going replacing one of the relays on the board and try and repair the blown printed track. Thanks

    November 28, 2012 at 12:46 am in reply to: siemens dishwasher #385474
    RHrepairs
    Participant

    Re: siemens dishwasher

    Goosed as in the motor is for the bin. Its definitely not water starvation and its not the capacitor. Where abouts is the divertor valve in the heater box?

    April 27, 2012 at 12:27 pm in reply to: LG dishwasher OE error code #373939
    RHrepairs
    Participant

    Re: LG dishwasher OE error code

    one slight problem cant seem to find the pressure switch unless its integrated somewhere. I can see the motor, element, salt chamber,pump, antileak floatation device. The fill tube goes straight to the chamber on the side of the machine

    April 26, 2012 at 9:09 am in reply to: Miele Vacuum Cleaners #371088
    RHrepairs
    Participant

    Re: Miele Vacuum Cleaners

    as in the pcb on the motor….what component on the pcb usually has a bad soldering joint?

  • Author
    Posts
Viewing 13 posts - 61 through 73 (of 73 total)
1 2 3 4 5