rocker

Forum Replies Created

Viewing 15 posts - 901 through 915 (of 1,132 total)
1 2 3 … 60 61 62 … 74 75 76
  • Author
    Posts
  • October 15, 2008 at 9:18 pm in reply to: Whirlpool 3RLEC8646KQ (USA) T/D #265204
    rocker
    Participant

    Re: Whirlpool 3RLEC8646KQ (USA) T/D

    Eastlmark, you are correct, when I fitted new motor I checked this mirco out I am sure this is ok. many thanks for your help.
    John

    October 15, 2008 at 5:14 pm in reply to: Whirlpool 3RLEC8646KQ (USA) T/D #265202
    rocker
    Participant

    Re: Whirlpool 3RLEC8646KQ (USA) T/D

    Cheers Mike, glad you advised me on this, as I was concerned I couldn’t find fault, this machine also get a lot of use in a day nursery.

    John.

    October 13, 2008 at 8:25 pm in reply to: Zanussi/electrolux WJD1667W #265062
    rocker
    Participant

    Re: Zanussi/electrolux WJD1667W

    Helo many thanks John.

    October 11, 2008 at 9:24 am in reply to: Smeg A1-2SE #264831
    rocker
    Participant

    Re: Smeg A1-2SE

    Thanks Bryan, will have a go.

    October 10, 2008 at 6:40 pm in reply to: Miele W803 (French import). Could I get armature skimmed? #264685
    rocker
    Participant

    Re: Miele W803 (French import). Could I get armature skimmed

    Are the brushes too lose in there guides this can cause them to arc or in this case just one maybe. you could have an intenal armature fault, need special equipment to test.
    John

    October 10, 2008 at 6:09 pm in reply to: Miele W803 (French import). Could I get armature skimmed? #264683
    rocker
    Participant

    Re: Miele W803 (French import). Could I get armature skimmed

    you dont usually need to skim the com unless badly worn or rewiring armature, com stick will bed in brushes for normal wear.
    best to use hard com stick first ,used by (armature winders) if problem persists best to take to armature winders to test & skim.
    Masterparts part No SE5504 about £5
    John.

    October 10, 2008 at 4:07 pm in reply to: Hotpoint WD64 #264771
    rocker
    Participant

    Re: Hotpoint WD64

    Cheers Dave & Wilf, sure its the rear vent as you both suggest, never checked this part last visit.

    John

    October 8, 2008 at 8:37 pm in reply to: Diplomat ADP8352 #264661
    rocker
    Participant

    Re: Diplomat ADP8352

    Tel. 01603630258 for spares John

    October 7, 2008 at 9:51 pm in reply to: Bosch import #264495
    rocker
    Participant

    Re: Bosch import

    Thanks Kwatt.
    John.

    October 5, 2008 at 7:22 pm in reply to: Smeg SUK62MFX5 #264218
    rocker
    Participant

    Re: Smeg SUK62MFX5

    Thanks Lawrence will do. John

    October 5, 2008 at 5:59 pm in reply to: Smeg SUK62MFX5 #264216
    rocker
    Participant

    Re: Smeg SUK62MFX5

    Eastlmark, not quite sure what you mean by change the square, dosent the stat fit directly into switch selector, I am not sure please let me know.
    Thanks John.

    October 3, 2008 at 7:29 pm in reply to: Smeg SUK62MFX5 #264214
    rocker
    Participant

    Re: Smeg SUK62MFX5

    cheers Lawerance, makes sense, was a bit conncerned as connect were advising to contact smeg for any tec info on this part.

    October 2, 2008 at 1:54 pm in reply to: Miele T689 #263696
    rocker
    Participant

    Re: Miele T689

    cheers Seamy, turned the job down as another engineer told me it is a long and difficult job.
    Cheers for your advice John

    September 29, 2008 at 7:40 pm in reply to: Miele T689 #263694
    rocker
    Participant

    Re: Miele T689

    Cheers Clayside. John

    September 27, 2008 at 6:42 pm in reply to: Diplomat ADP8332 #263553
    rocker
    Participant

    Re: Diplomat ADP8332

    Thanks for your replies gents, makes sense of fault given.
    Cheers John.

  • Author
    Posts
Viewing 15 posts - 901 through 915 (of 1,132 total)
1 2 3 … 60 61 62 … 74 75 76