rocker

Forum Replies Created

Viewing 15 posts - 961 through 975 (of 1,132 total)
1 2 3 … 64 65 66 … 74 75 76
  • Author
    Posts
  • March 11, 2008 at 11:25 am in reply to: Diplomat ADP3322 single oven #245462
    rocker
    Participant

    Re: Diplomat ADP3322 single oven

    Thanks for reply NWAR will contact them. John.

    March 7, 2008 at 9:27 pm in reply to: Mobile Phone repairer #245093
    rocker
    Participant

    Re: Mobile Phone repairer

    Hi Jim, phoneshop-uk in Nottingham, was the company I was looking for.
    well done. cheers John

    March 6, 2008 at 11:20 am in reply to: Mobile Phone repairer #245091
    rocker
    Participant

    Re: Mobile Phone repairer

    Hi Martin, thanks for reply but this isn’t the company I am looking for, the one I need repairs hardware ie.broken screens ect. at low cost
    Cheers John

    February 23, 2008 at 12:36 pm in reply to: WMA46 BOARD #243997
    rocker
    Participant

    Re: WMA46 BOARD

    Had simular fault on a hotpoint ,water was splashing onto interlock via small split in door gasket ,but no sign of water on floor. worth a check!
    John

    February 23, 2008 at 11:28 am in reply to: Beko VMA 510W #244024
    rocker
    Participant

    Re: Beko VMA 510W

    Hi Mike, no I havent, do these tend to come loose or go open circuit and can they be purchased if required, proberly take one with me on call back
    Cheers John

    January 24, 2008 at 7:56 am in reply to: Creda Hob 42257 #240826
    rocker
    Participant

    Re: Creda Hob 42257

    Cheers Steve, will be ordering. John

    January 22, 2008 at 9:00 am in reply to: Zanussi FS1255W washer #240491
    rocker
    Participant

    Re: Zanussi FS1255W washer

    Thanks Martin & Steve for your advice, after all that, she has decided to buy new machine.
    Martin, No I dont have TDS disc, looked up error codes and printed.
    Cheers John.

    January 15, 2008 at 10:38 pm in reply to: Blomberg 1501AAA washing machine #239770
    rocker
    Participant

    Re: Blomberg 1501AAA washing machine

    cheers chris, will do. John

    January 14, 2008 at 11:23 pm in reply to: Bosch SHV4313GB/13 #239647
    rocker
    Participant

    Re: Bosch SHV4313GB/13

    Hi Paul, the door dosen’t drop below 90 degs…but were the hinges bolt up on the inner door, the flat edge on the door is slightly distorted, ..so I feel you are right and does require a new inner door.
    many thanks cheers John

    January 3, 2008 at 1:30 pm in reply to: Top Loader USA Whirlpool #238345
    rocker
    Participant

    Re: Top Loader USA Whirlpool

    have been able to find model number and ordered part . thanks John

    December 28, 2007 at 10:35 pm in reply to: Bosch SGS43A42UK/01 #238082
    rocker
    Participant

    Re: Bosch SGS43A42UK/01

    Paul , I will check this float unit out, and let you know if it works many thanks john

    December 28, 2007 at 8:58 pm in reply to: Bosch SGS43A42UK/01 #238080
    rocker
    Participant

    Re: Bosch SGS43A42UK/01

    nomadpaul.
    when the machine starts ,it fills to correct level, runs program so it appears to have fault near end of cycle, could it still be impellor fault!!
    and is the impellor in side tank ? and can it be repaired/replaced never worked on this machine before. John

    December 18, 2007 at 10:44 pm in reply to: White Knight WK767 #237422
    rocker
    Participant

    Re: White Knight WK767

    Thanks Bryan, I guess you are right, I cant find this model number on connect site. John

    December 12, 2007 at 9:02 pm in reply to: Hotpoint WD860P #236252
    rocker
    Participant

    Re: Hotpoint WD860P

    cheers learch, thanks for advice I also feel its a board fault john

    December 9, 2007 at 2:14 pm in reply to: whirlpool (usa) Top loader #236660
    rocker
    Participant

    Re: whirlpool (usa) Top loader

    Cheers Steve will do.

  • Author
    Posts
Viewing 15 posts - 961 through 975 (of 1,132 total)
1 2 3 … 64 65 66 … 74 75 76