[rub]

Re: Bekp wma765

Fault ‘IL’ indicates a faulty pcb on that range.
Rub

[rub]

Re: Manufacturer requiring Service Repair Agents

Thats great, Thanks for the prompt reply.

[rub]

Re: Manufacturer requiring Service Repair Agents

Hi anybody heard anything back from this? i was asked to fill in a questionaire and return.I did this weeks ago but still nothing, I have emailed again to see the progress. I suppose its just a no.

[rub]

Re: Small kitchen appliance retailers

That’s great thanks for the reply

[rub]

Re: Zanussi FLE1115 won’t start

E34 is a faulty Electronic pressure switch, hopefully got you before you paid for the board

Rub

[rub]

Re: Whirlpool help please

Thanks for that the motor is bloody expensive so didnt want to rush in

[rub]

Re: Risk Assessments

Thanks for the replies. I naively thought experience and common sense were enough! However when it comes to it and the “ambulance chasers” get involved it becomes a mess. Since the court case and the HSE inspection we have been dragged through the coals on things you wouldnt even think were an issue. I now make sure I am fully compliant in all issues it does take a lot of time and effort which no doubt could be spent EARNING money instead of spending it!.Little things like, We issued everybody with toe tectors goggles gloves etc but we didnt get a sheet signed to say they had recieved them, so legally no proof they had them all weighs in the employees favour. I wanted to highlight this issue as i know from personnal experience what a nightmare it can become. I thought all my staff were great and the rest still are(fingers crossed), but one D*!khead ruins it for everyone. He saw an easy couple of grand and sold us short.

I like the rest would like to think common sense and living in the real world counts for a lot unfortunately in this mine field its the employers who carry all the risk.

It may be worth thinking about as you never know whats round the corner.

Incidentally he ‘injured’ himself installing a w/machine and with 30 years expierence you would think he knew what to do. He had a trolley which he used but claimed he was never trained in the correct operation.

[rub]

Re: service force agents ?

Hi simon,

I am serviceforce wirral/cheshire/liverpool/north wales

Shoot from your hip, your good hip. Alan Partridge 1998

paul

[rub]

Re: AEG Callout Charge

Hi just to let you know we charge £63.50+vat

Paul Dbe

[rub]

Re: famous customers?

Been to a few. Michael Owen (Northop), Paul Ince (Heswall) Tried on his england cap. Ricky Tomlinson (Aigburth) surprisingly grumpy. Ken Dodd( a horrible man), Roy Cropper ( Coronation st, well chester) Afew other footballers and a couple of has been popstars.

[rub]

Re: zwd 16581 washer dryer just shos error in display

dont scrap it just yet the most common fault by far are the dryer elements going short circuit this scrambles electronics. Easeist way of finding out jst disconnect the element if it works normally hey presto.
Hope this helps

Rub

[rub]

Re: AEG – SANTO 75348 – PROD: 928405224

Hi Sparky. the most likely fault will be the defrost element, when these fail the ice in the evaporator builds up and stops the air flow to the fridge. The fridge runs solely off the air being blown up from the freezer evaporator. There are 2 heaters on this product check them both one is wrapped around the freezer evaporator the other is stuck(double sided tape) on the panel directly below the evaporator. The sticky heater is a doddle to change pity i cant say the same about the other one.

Hope this helps.

Rub

[rub]

Re: AEG favorit 86070VI dishwasher

do you have the pnc/product number?

[rub]

Re: RANGEMASTER 55

Thanks for the quick reply, is there just one type?

[Author]

Posts