Simon46

Forum Replies Created

Viewing 15 posts - 1,306 through 1,320 (of 2,216 total)
1 2 3 … 87 88 89 … 146 147 148
  • Author
    Posts
  • January 29, 2007 at 9:43 am in reply to: Indesit WIL133 RECALL – Safety Issue #202467
    Simon46
    Participant

    Re: Indesit WIL133 RECALL – Safety Issue

    Got one to look at for leaking today. Should i refer to indesit?

    Regards
    S.

    January 28, 2007 at 6:33 pm in reply to: Bosch SGV43A03GB No Power #200757
    Simon46
    Participant

    Re: Bosch SGV43A03GB No Power

    Is the fault the same as when it first went faulty? just thinking it may be something that has blown the board again.

    Regards
    Simon

    January 28, 2007 at 4:33 pm in reply to: large syringe #153472
    Simon46
    Participant

    Re: large syringe

    Got the omnitron and it works a treat. into sump press button and empty it does. Put in water first or the end starts to oscillate and sounds like one of those rampant ladies toys 😆 .

    S.

    January 28, 2007 at 2:01 pm in reply to: hotpoint aquarius 1100 WD63 #202487
    Simon46
    Participant

    Re: hotpoint aquarius 1100 WD63

    Drain hose (grey) to ground level in bucket. Gravity will do the rest 🙂

    Regards
    Simon

    January 28, 2007 at 11:35 am in reply to: Schreiber APP6302 #202471
    Simon46
    Participant

    Re: Schreiber APP6302

    Clear the drain hole first at the back of the fridge (inside) where the water runs down the back wall to. Then see what happens.

    Regards
    Simon

    January 26, 2007 at 6:08 pm in reply to: Rangemaster 110 fan motor #201187
    Simon46
    Participant

    Re: Rangemaster 110 fan motor

    Thanks Dave fitted today. The blow/speed is amazing. Advised cust to recalibrate her cooking times 😀

    Regards
    Simon

    January 26, 2007 at 5:47 pm in reply to: HOTPOINT WMA BEARINGS #202376
    Simon46
    Participant

    Re: HOTPOINT WMA BEARINGS

    with shorter shoelaces :rotfl:

    S.

    January 26, 2007 at 5:24 pm in reply to: large syringe #153468
    Simon46
    Participant

    Re: large syringe

    Came across this batt operated pump in B&Q today. Bit more expensive than on

    http://www.omnitron.co.uk/products/?s=9

    S.

    January 26, 2007 at 7:26 am in reply to: Zanussi FB560 main oven hinges #202005
    Simon46
    Participant

    Re: Zanussi FB560 main oven hinges

    Thanks guys. Due to sockets thin on the ground replacement oven being fitted.

    S.

    January 25, 2007 at 11:19 pm in reply to: Diplomat 8702 washer dryer module #201774
    Simon46
    Participant

    Re: Diplomat 8702 washer dryer module

    sigh of relief 🙂

    thanks mark.

    S.

    January 25, 2007 at 10:17 pm in reply to: Bosch Classixx 1000 Washing Machine Hinge #202334
    Simon46
    Participant

    Re: Bosch Classixx 1000 Washing Machine Hinge

    Please post ENR number around door area.

    Regards
    Simon

    January 25, 2007 at 10:11 pm in reply to: Diplomat 8702 washer dryer module #201772
    Simon46
    Participant

    Re: Diplomat 8702 washer dryer module

    Part number of module originally fitted is 546023701 DMPA H7.9 1200RPM.
    Ordered EMW and received DMPA 9 H7. Notice resistors are 5K6 on new module. Old faulty module has 6K2 resistors fitted. Is this wrong and going to fail?
    Also 2H10mins job took cause mate fitted kitchen with leaking and swivelly push fit plumbing with taps and waste miles away from collapsing water damaged cupboard and 2 inch thick floor up to machine :rolls:

    Regards
    Simon

    January 22, 2007 at 11:37 pm in reply to: Diplomat 8702 washer dryer module #201771
    Simon46
    Participant

    Re: Diplomat 8702 washer dryer module

    Ta Mark 😆

    S.

    January 22, 2007 at 3:45 pm in reply to: Hotpoint 9525W timer no rinse fill #201744
    Simon46
    Participant

    Re: Hotpoint 9525W timer no rinse fill

    Thank you all.

    S.

    January 22, 2007 at 3:43 pm in reply to: Diplomat 8702 washer dryer module #201769
    Simon46
    Participant

    Re: Diplomat 8702 washer dryer module

    No / after model number on front of unit. Does that mean its a zero then?
    Trying to avoid deinstall as dishwasher next to it has a nice square cut in floor replaced with nearly matching laminate :rolls:

    Regards
    S.

  • Author
    Posts
Viewing 15 posts - 1,306 through 1,320 (of 2,216 total)
1 2 3 … 87 88 89 … 146 147 148