SL

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 31 total)
1 2 3
  • Author
    Posts
  • November 28, 2018 at 7:44 pm in reply to: Trainee appliance repair engineer #459243
    SL
    Participant

    where do you live?

    May 24, 2016 at 8:56 pm in reply to: Zanussi ZDF 14001SA fill problems. #437692
    SL
    Participant

    Re: Zanussi ZDF 14001SA fill problems.

    You must fit the air trap kit, fitting another sensor on its own will fail.

    May 21, 2016 at 9:29 pm in reply to: Zanussi ZDF 14001SA fill problems. #437690
    SL
    Participant

    Re: Zanussi ZDF 14001SA fill problems.

    There is a modification for the pressure sensor on these, order a new sensor and you get a kit to fit.

    May 21, 2016 at 9:26 pm in reply to: John Lewis WM1411 (Zanussi 914531500) #437749
    SL
    Participant

    Re: John Lewis WM1411 (Zanussi 914531500)

    The fault is the power pcb at the back or a low insulation on the wash element.

    May 21, 2016 at 9:19 pm in reply to: Beko washer problems #437575
    SL
    Participant

    Re: Beko washer problems

    Change the NTC, it comes with the element.

    June 20, 2015 at 10:37 pm in reply to: BEKO BC73F FRIDGE OVER FREEZING #427975
    SL
    Participant

    Re: BEKO BC73F FRIDGE OVER FREEZING

    disconnect the sensor connection at the pcb and it will run on time 20mins on 35 off

    October 17, 2014 at 10:57 pm in reply to: Stoves Richmond 900E Hob flashing E4 #420186
    SL
    Participant

    Re: Stoves Richmond 900E Hob flashing E4

    This code means no communication between the induction power board and the interface. It is actually caused by a loose link on the mains terminal block. We have had a few of these do this. The code sends you looking everywhere except the right place.

    May 17, 2012 at 6:28 pm in reply to: Beko American Style FF AP930X freezing in fridge? #375066
    SL
    Participant

    Re: Beko American Style FF AP930X freezing in fridge?

    The evap fan in the freezer is running slow or stopped which causes the fridge to freeze in the bottom section, change the fan motor.

    May 12, 2012 at 10:36 am in reply to: Zanussi ZWF12070W #374816
    SL
    Participant

    Re: Zanussi ZWF12070W

    Change the motor, well known problem

    March 22, 2012 at 11:51 pm in reply to: daewoo sticking #371852
    SL
    Participant

    Re: daewoo sticking

    It can be an unbalanced load, but if this is not the case change the PCB. Fitted quite a few for this problem.

    November 29, 2010 at 7:40 pm in reply to: Zanussi ZKT631DX E3 fault #337383
    SL
    Participant

    Re: Zanussi ZKT631DX E3 fault

    Link missing or loose on Terminal block

    September 21, 2010 at 10:18 pm in reply to: Indesit washing machine explodes #330627
    SL
    Participant

    Re: Indesit washing machine explodes

    Third point is correct, you need common sense and a good personality and the dont give out degrees for that.

    March 22, 2010 at 9:03 pm in reply to: contract work #315941
    SL
    Participant

    Re: contract work

    Lee, you made me smile with that last post, the funniest statements are the ones closest to the truth.

    January 27, 2010 at 11:00 pm in reply to: JTM again! #309900
    SL
    Participant

    Re: JTM again!

    Is there any positive news on JTM?

    Or does all Engineers have the same story.

    I have been asked to do work for a brand that has its warranty calls covered by JTM, are they the same with all brands or just the Servis etc

    November 20, 2009 at 7:46 pm in reply to: Belling problems.. #304312
    SL
    Participant

    Re: Belling problems..

    E3 = Not Heating
    Check the obvious heater o/c etc
    If heater ok, change the pressure switch nearest the front kick panel or you can try the adjust 1 complete turn clockwise, this will bring in more water which can be a problem on these.

    Depending on serial number there is a small pressure sensor on the tube connected to the floe through heater this also gave problems and stopped the heater from working. And yes its Chinese!

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 31 total)
1 2 3