[sparkey]

Re: Anglo Iberian

anyone recieved payment yet, still nothing here.

I have been promised a cheque by the middle of this week 🙂 will keep you posted.

Regards
Sparkey

[sparkey]

Re: Anglo Iberian

Kwatt wrote

Anyone been paid yet as I’ve yet to see a bean?

Nothing received as yet, twice this week I have chasers for completion of two outstanding calls, on both occasions told them they are on stop for non payment of account they then lost all interest in conversation ❓

Regards
Sparkey

[sparkey]

Re: Siemens/ Bosch motor end cap

Is the end cap assembly or overload housing on motor number 141344 available as a separate spare?

No end frame is listed for this motor, I always use end frame from earlier model without any problems.

Part no. 496872 retail price £31.00+vat

Regards
Sparkey

[sparkey]

Re: Anglo Iberian

According to JTM they will be honouring all engineers invoices, they have not yet got all details fom AIS.

Sparkey

[sparkey]

Re: indesit D61 leak reasons …

eastlmark wrote:why dont the low end makers just remove the drip tray and float

Then remove every thing above that to a skip leaving the best leak free appliance in the world.

Sparkey

[sparkey]

Re: Anglo Iberian

kwatt wrote

AIS has been bought by JTM this afternoon.

Any AIS agents received payments for last couple of months? has any body had any official confirmation of take over in writing?, have spoken to JTM earlier this week, sniffy woman very disinterested said all agents have received letter, NOT ME.

Is this about to be another Homark-Caremark-Bernstein situation?

Regards
Sparkey

[sparkey]

A quick thank you

Just a quick thank you to Rob for the training day in Norwich recently, very informative, information gained has been passed to customers almost daily. as you said it impresses them when you have the information ‘on tap’ to solve almost all of their washing / dishwashing problems.

Again many thanks

Regards
Sparkey

[sparkey]

Re: Whirpool W120

Thanks for that P45.

Regards
Dennis

[sparkey]

Re: Candy Aquaviva 1300

Thank you both, waiting for more information from customer, not a make I normally repair, just trying to do a favour for my regular spares delivery driver (got to keep them sweet) 😉

[sparkey]

Re: SMEG DWD612SS DISHWASHER

Knew I shouldnt have got involved 😡 just come back to haunt me.

Fault still as before all lights on left hand side of door on, fourth from left of lights on right of door on, fault code in instruction book say’s E8 “anomily in water distribution”

top / bottom distribution valve was replaced in Jan.

Now all heated wash programmes fault out as above some time into cycle, water hot, dispencer door opened.

Cold programmes work correctly

No earth faults found, water levels correct

Any advice?

Regards
Sparkey

[sparkey]

Re: Repairs@ – New Manufacturers Added

Kwatt wrote

What is Maxmatic then?

Maxmatic is a BRITISH made waste disposer, very solid well made appliance, competes in quality with Tweeny/ In-Sink.

Regards
Sparkey

[sparkey]

Re: Repairs@ – New Manufacturers Added

Kwatt wrote

I’ve added both In-Sink Erator

Can you add In-Sink-Erator to my list of Manufacturers please also how about Maxmatic? I repair those also.

Still a repairs @ virgin at moment but ever hopefull 😉

Regards
Sparkey

[sparkey]

Re: Bosch Fridge freezer – KGV-2604-GB/05

Both sensors are in the refrigerator section, one is for air temperature control the other (the one that fails) is for fridge evaporator defrost temperature control, hence when it fails the control module will not turn the compressor on.

There is no control whatsoever on the freezer temperature, it has been calculated in the design that when the fridge is at +5 the temperature in freezer should be minimum of -18.

This appliance must be installed in a room temperature of at least +12 or that can also give problems with compressor run times.

There has been much discussion about the sensor bypass in other postings in this forum, use the search facility to find it

Regards
Sparkey

[sparkey]

Re: Bosch d/w heater failures

I have fitted many of these heaters over the last twelve months, for the last three months i have quizzed the customers and find that all have regually used or always use 3 or 4 in one tablets with no salt in water softener.

I personally think this is more likely to be the reason for failure.

Interestingly I have never had to replace an element that I have previously replaced where the customer is now using seperate detergent – salt – rince aid.

Regards
Sparkey

[sparkey]

Re: Neff fan oven elements

dave_conway wrote

Are these holes drilled all the way through the fan blade

they are drilled right through the fan blade, six if I remember correctly approx 5mm dia., (too cold to go and look in the van right now)

Regards
Sparkey

[Author]

Posts