[TeeMyob]

Re: Samsung rsh1 jbrs makes ice but wont tip it into hopper.

Hello,

In my experience ( I see a lot of these). Always been the ice maker. Only ever had a couple of RS21 Series where the PCB/Module was to blame.

TM

[TeeMyob]

Re: ASD (leeds) Still going?

Hello,

Sorry to hear that. Always seemed so go to deal with.

Hope you get sorted soon.

TM

[TeeMyob]

Re: Liebherr fridge sensor

As I understand it, my facts are right?

[TeeMyob]

Re: Liebherr fridge sensor

Hello,

Why do you think it is the sensor?

I would say easy.

But the main Service Network for Liebherr have gone bust. You might want to try Liebherr UK or you local authorised agent.

TM

[TeeMyob]

Re: samsung rsh1 dtmh freezer not cooling

Hello Sounds like it is short of refrigerant.

Same compressor – different evaporators.

Sounds like there is only enough to fulfil the fridge requirements.

Otherwise maybe a restricted evap capillary

TM

[TeeMyob]

Re: F-Gas Certificate

Thank You.

Will be looking to do R134a R407C work

TM

[TeeMyob]

Re: LPR600 LPR600/1 Dishwasher Fault Flashes

Is this what I might be looking at or is this the wrong series/range?

Curtasy of Rocks1

Whirlpool Dishwasher Error codes.

F0. 10 flashes. Sensor Break (Only shown in test programme. Not visible to customer).

F1. Single flash. NTC Break. NTC open circuit/short circuit or ambient temperature less than 3 Celcius

F2. 2 Flashes. Water leakage. Floater switch LS6 in drip tray has switched.

F3. 3 Flashes. Heating system defect. Heater or relay on control board defect. Chack also cabling.

F4. 4 Flashes. Draining failure. Drain pump, control board OWI or water indicator defect.

F5. 5 Flashes. Sprayarm Blocked (not present on VBL version. On 1 digit display will show as F and flashing start led).

F6. 6 Flashes. Water valve (WV1) is switched on but flow meter (FM) senses no impulses (less than 10 impulses in 10 secs) and the water indicator (WI) is at a low level
Water Valve Closed. Water inlet hose blocked.
Water inlet valve (WV1) defective. Flow meter (FM) defective (leads to FM failure)

F7. 7 Flashes. Flow meter failure. Flow meter defect. Water inlet valve defect or water inlet hose blocked.

F8. 8 Flashes. Water level failure. Sieve strongly dirty or big amount of foam inside to less water.

F9. 9 Flashes. Continuously Water Inlet. Water inlet valve mechanically not closed or control board defect.

FA. 11 Flashes. OWI failure. Dirty OWI lens. OWI defect or control board defect. Check cabling.

FB. 12 Flashes. Motorised Diverter Valve

FC. 13 Flashes. Water Hardness Sensor Failure

A fault with no fault code indication = faulty module

These codes should cover the entire range of Whirlpool dishwashers.

Test Mode

Make sure the appliance is empty of water before running Diagnostics as it does not pump out before starting to fill and therefore you could overfill the appliance.
Open the door and set the program to the first program. (Normally rinse).
Turn the power off.
Press and hold the start button and while holding turn the power on.
After a little while the start button will flash, release the button.
Press the start button once and close the dishwasher door.
The machine will now run through a diagnostic routine.
If memory serves me right it takes about 20 mins.
The machine will stop during diagnostics if an error is found and will display the error code. If no error is found it will complete the diagnostics and end the programme.

To exit diagnostics at any time just press and hold the start button till the programme is cancelled.

Read more: http://www.diynot.com/forums/viewtopic. … z24yBBNMgm

[TeeMyob]

Re: Diplomat HJA8552 Washing machine Error Code

Thanks for all the replies folks.

The Fault was the thermostat.

TM

[TeeMyob]

Re: Fisher & Paykal Dish Drawer Fault Code

Thanks once again John.

I will let you know which one it is/was.

TM

[TeeMyob]

Re: Diplomat HJA8552 Washing machine Error Code

Looks like I might have to do a multiple order of parts!

[TeeMyob]

Re: Fisher & Paykal Dish Drawer Fault Code

Morning Folks!

I now have another one.

Heater plate definitely blown – Replaced, top drawer still dead.
Replaced front PCB – Still dead.

Might bring this one into the workshop, see if we can get a solution.

TM

[TeeMyob]

Re: AEG & Zanussi/Electrolux Frost Free – Fridge not cooling

Can be fan motor or module fault. Fans sieze, modules skip defrost.

Also beware of low refrigerant (leaks). Or, compressor issues . This can fool you into the aforementioned.

Heaters and sensors rarely fail.

TM

[TeeMyob]

Re: Electrolux F/Freezer Fridge Not Cooling

Can be fan motor or module fault. Fans sieze, modules skip defrost.

Also beware of low refrigerant (leaks). Or, compressor issues . This can fool you into the aforementioned.

Heaters and sensors rarely fail.

TM

[TeeMyob]

Re: Diplomat Fridge Freezer – AMP 6826 – Fridge not cooling

Hello,

If it is the one with the blue display or central module.

If you have ice (or rather white hoar frost) on the freezer evaporator, no defrost is taking place.

If this is the case when you reveal the evap. Turn off the appliance at the wall and wait a couple of minutes and then power up again.

The unit should default into an automatic defrost. If it does not, most likely cause is freezer evap defrost sensor fault.

If the evap is a mixture of ice & frost. Customer may have left the door open (though never admit it unless only on an agreed or no call-out).

If the evap is clear, may be fan. There is a reed magnet switch to the right of the door. Close the circuit with a magnet. If the fan does not run, check for voltage at the fan.

Any help?

TM

[TeeMyob]

Re: LG FRIDGE FREEZER

Check the auger turns on load.

Open door, hold button for light in and request ice via the door.

The Auger may not turn under load or may be spinning off the nut or clip.

Check for power at the AUGER (240v) when you request ice.

TM

[Author]

Posts