telemek

Forum Replies Created

Viewing 13 posts - 31 through 43 (of 43 total)
1 2 3
  • Author
    Posts
  • December 6, 2012 at 7:22 pm in reply to: Zanussi wont start #385924
    telemek
    Participant

    Re: Zanussi wont start

    Thanks for your quick reply repman, will try that but machine is a long way away so may be a day or two, but will let you know.

    June 28, 2012 at 9:56 am in reply to: Hotpoint FFP187B fridge freezing #353264
    telemek
    Participant

    Re: Hotpoint FFP187B fridge freezing

    main pcb replaced all ok

    March 27, 2012 at 9:49 am in reply to: Whirplool ADG644IX configure PCB #370236
    telemek
    Participant

    Re: Whirplool ADG644IX configure PCB

    Have changed board with 481221838336 which is the one they say is configured for this machine, but now fills then washes for a few seconds stops and washes for 5 or 6 times then drains with 11 flashes.
    Any ideas please?

    March 3, 2012 at 2:45 pm in reply to: Whirplool ADG644IX configure PCB #370235
    telemek
    Participant

    Re: Whirplool ADG644IX configure PCB

    Thanks for that John, will return board and get the configured one.

    March 3, 2012 at 12:04 pm in reply to: Whirplool ADG644IX configure PCB #370233
    telemek
    Participant

    Re: Whirplool ADG644IX configure PCB

    Number on board is 461972750951 and number on machine is 851164415853. Hope this helps.

    March 3, 2012 at 10:47 am in reply to: Whirplool ADG644IX configure PCB #370231
    telemek
    Participant

    Re: Whirplool ADG644IX configure PCB

    Thanks for your reply, the part no is 480140102482.

    September 2, 2011 at 8:27 am in reply to: AWG5122 washer error lights #357873
    telemek
    Participant

    Re: AWG5122 washer error lights

    Water not getting away due to blocked drain outlet under sink. all ok now

    June 9, 2011 at 8:28 am in reply to: WFF2466GB/07 #347612
    telemek
    Participant

    Re: WFO2466GB/07

    Did you find an answer to this one as I have the same problem, checked heater going to try NTC. 😕

    May 4, 2011 at 8:30 am in reply to: Whirlpool ADG644 not heating #350377
    telemek
    Participant

    Re: Whirlpool ADG644 not heating

    Thanks nigegt, checked wiring, you were spot on, broken wire at bottom of door going to heater, working fine now. Many thanks

    September 24, 2009 at 7:59 am in reply to: Whirlpool AWM865 continuos tumble #297797
    telemek
    Participant

    Re: Whirlpool AWM865 continuos tumble

    Thanks for your reply, I had a feeling the timer may have been the cause, time for a replacement.

    July 29, 2009 at 10:17 am in reply to: whirlpool AWO/D 4505 wont spin #293364
    telemek
    Participant

    Re: whirlpool AWO/D 4505 wont spin

    Hi Payney

    Thanks for your reply, I will check tacho coil & connections.

    Graham

    July 9, 2008 at 8:00 am in reply to: Siemens KG31V20GB – not cooling #257128
    telemek
    Participant

    Re: Siemens KG31V20GB – not cooling

    Good morning
    Tried bypassing sensor as per previous post (shorting dark blue & brown wires) but same fault, re-connected & bypassed other sensor (light blue & black) and checked temp after 12 hours and everything to be working fine. Will update if any problems.
    Thanks for your help.

    July 7, 2008 at 10:26 am in reply to: Siemens KG31V20GB – not cooling #257127
    telemek
    Participant

    Re: Siemens KG31V20GB – not cooling

    Simon
    Thanks for your reply, I will try the by-pass later today & let you know the result.
    regards Graham

  • Author
    Posts
Viewing 13 posts - 31 through 43 (of 43 total)
1 2 3